Kevin Chiu has uploaded this change for review.
mb/google/guybrush/nipperkin: update nipperkin config
copy config from guybrush reference board.
BUG=b:194031783
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I58a9b8393a965a9c793802d3e660829863b74375
---
M src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb
1 file changed, 162 insertions(+), 0 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/63/57263/1
diff --git a/src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb b/src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb
index c182265..f75483d 100644
--- a/src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb
+++ b/src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb
@@ -1,7 +1,169 @@
# SPDX-License-Identifier: GPL-2.0-or-later
+fw_config
+ field USB_DB 0 1
+ option USB_DB_A1_PS8811_C1_PS8818 0
+ option USB_DB_A1_ANX7491_C1_ANX7451 1
+ end
+ field FORM_FACTOR 2
+ option FORM_FACTOR_CLAMSHELL 0
+ option FORM_FACTOR_CONVERTIBLE 1
+ end
+ field KB_BL 3
+ option KB_BL_ABSENT 0
+ option KB_BL_PRESENT 1
+ end
+ field FP 4
+ option FP_ABSENT 0
+ option FP_PRESENT 1
+ end
+ field WLAN 5 6
+ option WLAN_WCN6856 0
+ option WLAN_RTL8852 1
+ end
+ field WWAN 7 8
+ option WWAN_DIASABLED 0
+ option WWAN_L850GL 1
+ option WWAN_FM350GL 2
+ end
+ field BEEP_MODE 9
+ option BEEP_MODE_AMP 0
+ option BEEP_MODE_BIT_BANG 1
+ end
+end
chip soc/amd/cezanne
device domain 0 on
end # domain
+
+ register "slow_ppt_limit_mW" = "25000"
+ register "fast_ppt_limit_mW" = "30000"
+ register "slow_ppt_time_constant_s" = "5"
+ register "stapm_time_constant_s" = "275"
+ register "sustained_power_limit_mW" = "15000"
+ register "thermctl_limit_degreeC" = "100"
+
+ register "telemetry_vddcrvddfull_scale_current_mA" = "92165" #mA
+ register "telemetry_vddcrvddoffset" = "412"
+ register "telemetry_vddcrsocfull_scale_current_mA" = "30233" #mA
+ register "telemetry_vddcrsocoffset" = "457"
+
+ # I2C Config
+ #+-------------------+---------------------------+
+ #| Field | Value |
+ #+-------------------+---------------------------+
+ #| I2C0 | Trackpad |
+ #| I2C1 | Touchscreen |
+ #| I2C2 | Speaker, Codec, P-SAR |
+ #| I2C3 | H1/D2 TPM |
+ #+-------------------+---------------------------+
+ register "i2c[0]" = "{
+ .speed = I2C_SPEED_FAST,
+ }"
+
+ register "i2c[1]" = "{
+ .speed = I2C_SPEED_FAST,
+ }"
+
+ register "i2c[2]" = "{
+ .speed = I2C_SPEED_FAST,
+ }"
+
+ register "i2c[3]" = "{
+ .speed = I2C_SPEED_FAST,
+ .early_init = true,
+ }"
+
+ device ref i2c_0 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0000""
+ register "desc" = ""ELAN Touchpad""
+ register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_9)"
+ register "wake" = "GEVENT_22"
+ register "probed" = "1"
+ device i2c 15 on end
+ end
+ end # I2C0
+
+ device ref i2c_1 on
+ chip drivers/i2c/hid
+ register "generic.hid" = ""GDIX0000""
+ register "generic.desc" = ""Goodix Touchscreen""
+ register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_89)"
+ register "generic.probed" = "1"
+ register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_68)"
+ register "generic.enable_delay_ms" = "10"
+ register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_121)"
+ register "generic.reset_off_delay_ms" = "1"
+ register "generic.reset_delay_ms" = "10"
+ register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_120)"
+ register "generic.stop_delay_ms" = "170"
+ register "generic.stop_off_delay_ms" = "1"
+ register "generic.has_power_resource" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 5d on end
+ end
+ chip drivers/generic/gpio_keys
+ register "name" = ""PENH""
+ register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPIO_4)"
+ register "key.dev_name" = ""EJCT""
+ register "key.wakeup_event_action" = "EV_ACT_DEASSERTED"
+ register "key.linux_code" = "SW_PEN_INSERTED"
+ register "key.linux_input_type" = "EV_SW"
+ register "key.label" = ""pen_eject""
+ register "key.debounce_interval" = "100"
+ register "key.wakeup_route" = "WAKEUP_ROUTE_GPIO_IRQ"
+ device generic 0 on end
+ end
+ end # I2C1
+
+ device ref i2c_2 on
+ chip drivers/i2c/generic
+ register "hid" = ""10EC5682""
+ register "name" = ""RT58""
+ register "desc" = ""Realtek RT5682""
+ register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPIO_90)"
+ register "property_count" = "1"
+ register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
+ register "property_list[0].name" = ""realtek,jd-src""
+ register "property_list[0].integer" = "1"
+ device i2c 1a on end
+ end
+ chip drivers/i2c/generic
+ register "hid" = ""10EC1019""
+ register "desc" = ""Realtek SPK AMP L""
+ register "uid" = "0"
+ register "probed" = "1"
+ device i2c 28 on end
+ end
+ chip drivers/i2c/generic
+ register "hid" = ""10EC1019""
+ register "desc" = ""Realtek SPK AMP R""
+ register "uid" = "1"
+ device i2c 29 on end
+ end
+ chip drivers/i2c/generic
+ register "hid" = ""10EC1019""
+ register "desc" = ""Realtek SPK AMP L1""
+ register "uid" = "2"
+ register "probed" = "1"
+ device i2c 2a on end
+ end
+ end # I2C2
+
+ device ref uart_1 on
+ chip drivers/uart/acpi
+ register "name" = ""CRFP""
+ register "desc" = ""Fingerprint Reader""
+ register "hid" = "ACPI_DT_NAMESPACE_HID"
+ register "compat_string" = ""google,cros-ec-uart""
+ register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_21)"
+ register "wake" = "GEVENT_5"
+ register "uart" = "ACPI_UART_RAW_DEVICE(3000000, 64)"
+ device generic 0 on
+ probe FP FP_PRESENT
+ end
+ end
+ end
+
end # chip soc/amd/cezanne
To view, visit change 57263. To unsubscribe, or for help writing mail filters, visit settings.