January 2015 - flashrom - mail.coreboot.org

flashrom issue w/ Avoton platform
by Pierre-O Jan. 28, 2015

Jan. 28, 2015

hi folks ! I'm trying to use flashrom with an avoton/rangeley board, bios protections are disabled, chip is detected but simple read operation fails, here's my log : *flashrom v0.9.7-r1869 on Linux 3.13.0-24-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.2.1, GCC 4.8.2, little endian Command line (7 args): flashrom -V -p internal -c N25Q128..3E -r LFFF-backup.bin Calibrating delay loop... OS timer resolution is 1 usecs, 863M loops per second, 10 myus = 10 us, 100 myus = 104 us, 1000 myus = 1016 us, 10000 myus = 10017 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. Using Internal DMI decoder. DMI string chassis-type: "Desktop" DMI string system-manufacturer: "Insyde" DMI string system-product-name: "MohonPeak" DMI string system-version: "TBD by OEM" DMI string baseboard-manufacturer: "Type2 - Board Vendor Name1" DMI string baseboard-product-name: "Type2 - Board Product Name1" DMI string baseboard-version: "Type2 - Board Version" Found chipset "Intel Avoton/Rangeley" with PCI ID 8086:1f38. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Root Complex Register Block address = 0xfed1c000 GCS = 0x40000c01: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap: not enabled 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes SPI_BASE_ADDRESS = 0xfed01000 SPI Read Configuration: prefetching disabled, caching enabled, BIOS_CNTL = 0x01: BIOS Lock Enable: disabled, BIOS Write Enable: enabled 0x04: 0x6018 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=3, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=0 Programming OPCODES... done 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x50: 0x0000ffff (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff 0x54: 0x01ff0000 FREG0: Flash Descriptor region (0x00000000-0x001fffff) is read-write. 0x58: 0x07ff0200 FREG1: BIOS region (0x00200000-0x007fffff) is read-write. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf80000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0 0x94: 0x5006 (PREOP) 0x96: 0x463b (OPTYPE) 0x98: 0x05d80302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xC4: 0x0080d807 (LVSCC) LVSCC: BES=0x3, WG=1, WSR=0, WEWS=0, EO=0xd8, VCL=1 0xC8: 0x0000d807 (UVSCC) UVSCC: BES=0x3, WG=1, WSR=0, WEWS=0, EO=0xd8 0xD0: 0x00000000 (FPB) OK. The following protocols are supported: FWH, SPI. Probing for Micron/Numonyx/ST N25Q128..3E, 16384 kB: probe_spi_rdid_generic: id1 0x20, id2 0xba18 Found Micron/Numonyx/ST flash chip "N25Q128..3E" (16384 kB, SPI) mapped at physical address 0x00000000ff000000. Chip status register is 0x02. Chip status register: Status Register Write Disable (SRWD, SRP, ...) is not set Chip status register: Block Protect 3 (BP3) is not set Chip status register: Top/Bottom (TB) is top Chip status register: Block Protect 2 (BP2) is not set Chip status register: Block Protect 1 (BP1) is not set Chip status register: Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is set Chip status register: Write In Progress (WIP/BUSY) is not set This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). Reading flash... Transaction error! SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=0 Running OPCODE 0x03 failed at address 0x800000 (payload length was 64). Read operation failed! FAILED. Restoring MMIO space at 0x7f4c9ba1409c Restoring MMIO space at 0x7f4c9ba14098 Restoring MMIO space at 0x7f4c9ba14096 Restoring MMIO space at 0x7f4c9ba14094 Restoring MMIO space at 0x7f4c9ba140fc *Any idea ? Best regards, -- Pierre-O

3 4

Re: [flashrom] Flashrom reading/writing Pm25LV512 issue
by Stefan Tauner Jan. 27, 2015

Jan. 27, 2015

On Tue, 27 Jan 2015 22:36:03 +0200 Tudoran Mihail <mihail.tudoran(a)gmail.com> wrote: > Hello, > > I am encountering some issues trying to read a Pm25LV512 SPI flash from a > small LCD monitor, really got stuck at this point. > > Hardware: > - Pm25LV512 attached to a Weltrend WT8871 video IC > - Arduino UNO R3 with 16u2 USB<>Serial converter > - CD4050 to convert 5v to 3v3 > - Used the schematic provided on http://flashrom.org/Serprog/Arduino_flasher > to interface the chip > - Tried "in-circuit" programming without removing the chip from the board > - Wire length of less than 8cm. > > Software: > > - Latest serprog-duino from git > - Tried with flashrom v0.9.6.1-r1563 > - And with flashrom v0.9.7-r1711 > - Ubuntu 14.04 64bit > > I really appreciate any help I could get and can provide any info/logs > needed. > The result looks as if you are reading random data... either your connections are wrong/bad, or the board is disturbing the communication on the SPI bus. See also http://flashrom.org/ISP -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Flashrom reading/writing Pm25LV512 issue
by Tudoran Mihail Jan. 27, 2015

Jan. 27, 2015

Hello, I am encountering some issues trying to read a Pm25LV512 SPI flash from a small LCD monitor, really got stuck at this point. Hardware: - Pm25LV512 attached to a Weltrend WT8871 video IC - Arduino UNO R3 with 16u2 USB<>Serial converter - CD4050 to convert 5v to 3v3 - Used the schematic provided on http://flashrom.org/Serprog/Arduino_flasher to interface the chip - Tried "in-circuit" programming without removing the chip from the board - Wire length of less than 8cm. Software: - Latest serprog-duino from git - Tried with flashrom v0.9.6.1-r1563 - And with flashrom v0.9.7-r1711 - Ubuntu 14.04 64bit I really appreciate any help I could get and can provide any info/logs needed. Thanks ! Mihail. Output from flashrom: sudo flashrom -p serprog:dev=/dev/ttyACM0:115200 -VVVV flashrom v0.9.6.1-r1563 on Linux 3.13.0-43-generic (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.9, GCC 4.7.1, little endian Command line (3 args): flashrom -p serprog:dev=/dev/ttyACM0:115200 -VVVV Calibrating delay loop... OS timer resolution is 1 usecs, 1467M loops per second, 10 myus = 10 us, 100 myus = 110 us, 1000 myus = 1011 us, 10000 myus = 10317 us, 4 myus = 5 us, OK. Initializing serprog programmer serprog: connected - attempting to synchronize ... serprog: Synchronized serprog: Interface version ok. serprog: Bus support: parallel=off, LPC=off, FWH=off, SPI=on Warning: Automatic command availability check failed for cmd 0x8 - won't execute cmd Warning: Automatic command availability check failed for cmd 0x11 - won't execute cmd serprog: Programmer name is "serprog-duino" serprog: Serial buffer size is 65535 The following protocols are supported: SPI. Probing for AMIC A25L05PT, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0xf0 0x60 0xff 0xe8. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xf0, id2 0x60ff Probing for AMIC A25L05PU, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0x00 0xfe 0x00 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xfe00 Probing for AMIC A25L10PT, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0x30 0xfe 0x00 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x30, id2 0xfe00 Probing for AMIC A25L10PU, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0x02 0x1f 0x81 0x7f. probe_spi_rdid_generic: id1 0x02, id2 0x1f81 Probing for AMIC A25L20PT, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0xff 0x7f 0x00 0xbc. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x7f00 Probing for AMIC A25L20PU, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0xff 0x05 0x00 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x500 Probing for AMIC A25L40PT, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0x00 0xfc 0x90 0xb0. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xfc90 Probing for AMIC A25L40PU, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0x00 0xfc 0x80 0xe0. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xfc80 Probing for AMIC A25L80P, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0xf8 0xfa 0x08 0xff. probe_spi_rdid_generic: id1 0xf8, id2 0xfa08 Probing for AMIC A25L16PT, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0xff 0x47 0xfa 0x03. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x47fa Probing for AMIC A25L16PU, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0x80 0x7d 0xe0 0x10. probe_spi_rdid_generic: id1 0x80, id2 0x7de0 Probing for AMIC A25L512, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x17 0xfc 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x17, id2 0xfc00 Probing for AMIC A25L010, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x5f 0xe7 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x5f, id2 0xe7ff Probing for AMIC A25L020, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x08 0xff 0x00. probe_spi_rdid_generic: id1 0x08, id2 0xff00 Probing for AMIC A25L040, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x7d 0x01 0x0f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x7d, id2 0x10f Probing for AMIC A25L080, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x03 0x20. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x320 Probing for AMIC A25L016, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x7f 0x7e 0x08. RDID byte 1 parity violation. probe_spi_rdid_generic: id1 0x7f7e, id2 0x08 Probing for AMIC A25L032, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x03 0x1f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x31f Probing for AMIC A25LQ032, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x00 0x04. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x04 Probing for Atmel AT25DF021, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x79 0x00 0x7d. probe_spi_rdid_generic: id1 0x79, id2 0x7d Probing for Atmel AT25DF041A, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xe0 0x07 0x44. probe_spi_rdid_generic: id1 0xe0, id2 0x744 Probing for Atmel AT25DF081, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x7f 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x7fff Probing for Atmel AT25DF081A, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x08 0xff 0x03. probe_spi_rdid_generic: id1 0x08, id2 0xff03 Probing for Atmel AT25DF161, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xfc 0xe0 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xfc, id2 0xe000 Probing for Atmel AT25DF321, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x20 0x0f 0x00. probe_spi_rdid_generic: id1 0x20, id2 0xf00 Probing for Atmel AT25DF321A, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x0f 0xfe 0xe0. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x0f, id2 0xfee0 Probing for Atmel AT25DF641(A), 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xfc 0xfa. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xfcfa Probing for Atmel AT25DQ161, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x1f 0x21. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x1f21 Probing for Atmel AT25F512B, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x02 0x00 0x40. probe_spi_rdid_generic: id1 0x02, id2 0x40 Probing for Atmel AT25FS010, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x00 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x00 Probing for Atmel AT25FS040, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x01 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x100 Probing for Atmel AT26DF041, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xfd 0x0c 0x07. probe_spi_rdid_generic: id1 0xfd, id2 0xc07 Probing for Atmel AT26DF081A, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x20 0x01 0x00. probe_spi_rdid_generic: id1 0x20, id2 0x100 Probing for Atmel AT26DF161, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xe8 0x00 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xe8, id2 0xff Probing for Atmel AT26DF161A, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xf0 0x00 0x84. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xf0, id2 0x84 Probing for Atmel AT26F004, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x5f 0x80. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x5f80 Probing for Atmel AT45CS1282, 16896 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x80 0x60. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x8060 Probing for Atmel AT45DB011D, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x80 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x8000 Probing for Atmel AT45DB021D, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x1f 0x30 0x07. probe_spi_rdid_generic: id1 0x1f, id2 0x3007 Probing for Atmel AT45DB041D, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x0c 0x00 0xe7. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x0c, id2 0xe7 Probing for Atmel AT45DB081D, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x00 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x00 Probing for Atmel AT45DB161D, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0xff 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0xff00 Probing for Atmel AT45DB321C, 4224 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xfc 0xbe 0x7c. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xfc, id2 0xbe7c Probing for Atmel AT45DB321D, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x07 0x0c. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x70c Probing for Atmel AT45DB642D, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x9e 0x00 0xff. probe_spi_rdid_generic: id1 0x9e, id2 0xff Probing for EMST F25L008A, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xae 0x00 0x0c. probe_spi_rdid_generic: id1 0xae, id2 0x0c Probing for Eon EN25B05, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x03 0x00 0x38. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x03, id2 0x38 Probing for Eon EN25B05T, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x1f 0xfa 0x00. probe_spi_rdid_generic: id1 0x1f, id2 0xfa00 Probing for Eon EN25B10, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x0c 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xc00 Probing for Eon EN25B10T, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x0f 0x01. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xf01 Probing for Eon EN25B20, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xfe 0xc8 0xfd. probe_spi_rdid_generic: id1 0xfe, id2 0xc8fd Probing for Eon EN25B20T, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x02 0x00 0x3f. probe_spi_rdid_generic: id1 0x02, id2 0x3f Probing for Eon EN25B40, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xc0 0x5f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xc05f Probing for Eon EN25B40T, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x40 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x4000 Probing for Eon EN25B80, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x01 0x3f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x13f Probing for Eon EN25B80T, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x60 0x00 0xfe. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x60, id2 0xfe Probing for Eon EN25B16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x30 0x80 0x10. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x30, id2 0x8010 Probing for Eon EN25B16T, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xc3 0xd1 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xc3, id2 0xd100 Probing for Eon EN25B32, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x06 0x0b. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x60b Probing for Eon EN25B32T, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x02 0x04 0x00. probe_spi_rdid_generic: id1 0x02, id2 0x400 Probing for Eon EN25B64, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xff 0x41. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xff41 Probing for Eon EN25B64T, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x07 0xc4. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x7c4 Probing for Eon EN25F05, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x02 0xfc. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x2fc Probing for Eon EN25F10, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x04 0x00 0xff. probe_spi_rdid_generic: id1 0x04, id2 0xff Probing for Eon EN25F20, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x71 0x02 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x71, id2 0x200 Probing for Eon EN25F40, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x1f 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x1fff Probing for Eon EN25F80, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x38 0x00 0x00. probe_spi_rdid_generic: id1 0x38, id2 0x00 Probing for Eon EN25F16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x08 0x7f 0x08. probe_spi_rdid_generic: id1 0x08, id2 0x7f08 Probing for Eon EN25F32, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xfe 0xe0. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xfee0 Probing for Eon EN25Q40, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xf8 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xf800 Probing for Eon EN25Q80(A), 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xfe 0x60 0x00. probe_spi_rdid_generic: id1 0xfe, id2 0x6000 Probing for Eon EN25Q16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x2f 0x00 0x80. probe_spi_rdid_generic: id1 0x2f, id2 0x80 Probing for Eon EN25Q32(A/B), 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x3c 0x7f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x3c7f Probing for Eon EN25Q64, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x08 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x800 Probing for Eon EN25Q128, 16384 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x08 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x800 Probing for Eon EN25QH16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x7d 0xc0. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x7dc0 Probing for Eon EN25QH32, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x79 0x00 0x40. probe_spi_rdid_generic: id1 0x79, id2 0x40 Probing for GigaDevice GD25Q20, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x13 0x18 0x00. probe_spi_rdid_generic: id1 0x13, id2 0x1800 Probing for GigaDevice GD25Q40, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x03 0x10 0x02. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x03, id2 0x1002 Probing for GigaDevice GD25Q80, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x87 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x8700 Probing for GigaDevice GD25Q16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x6f 0xf8 0xf2. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x6f, id2 0xf8f2 Probing for GigaDevice GD25Q32, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x3f 0x00 0x80. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x3f, id2 0x80 Probing for GigaDevice GD25Q64, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x30 0x00 0x80. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x30, id2 0x80 Probing for GigaDevice GD25Q128, 16384 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x04 0xff 0x00. probe_spi_rdid_generic: id1 0x04, id2 0xff00 Probing for Macronix MX25L512, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x20 0x80. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x2080 Probing for Macronix MX25L1005, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xfa 0x80 0x7f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xfa, id2 0x807f Probing for Macronix MX25L2005, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x07 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x700 Probing for Macronix MX25L4005, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x05 0x28 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x05, id2 0x28ff Probing for Macronix MX25L8005, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xe0 0x60 0x3f. probe_spi_rdid_generic: id1 0xe0, id2 0x603f Probing for Macronix MX25L1605, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x10 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x1000 Probing for Macronix MX25L1635D, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xfd 0xff 0x00. probe_spi_rdid_generic: id1 0xfd, id2 0xff00 Probing for Macronix MX25L1635E, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xe0 0xe0 0x00. probe_spi_rdid_generic: id1 0xe0, id2 0xe000 Probing for Macronix MX25L3205, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xfe 0xbe. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xfebe Probing for Macronix MX25L3235D, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x3f 0x01 0x18. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x3f, id2 0x118 Probing for Macronix MX25L6405, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x30 0xff 0x90. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x30, id2 0xff90 Probing for Macronix MX25L12805, 16384 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xf8 0x00 0x7f. probe_spi_rdid_generic: id1 0xf8, id2 0x7f Probing for Numonyx M25PE10, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xf0 0x04. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xf004 Probing for Numonyx M25PE20, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x3f 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x3f00 Probing for Numonyx M25PE40, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xf7 0xfb 0xfe. probe_spi_rdid_generic: id1 0xf7, id2 0xfbfe Probing for Numonyx M25PE80, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x61 0xc2 0x3f. probe_spi_rdid_generic: id1 0x61, id2 0xc23f Probing for Numonyx M25PE16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x00 0x80. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x80 Probing for Numonyx N25Q064, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xd1 0x17 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xd1, id2 0x17ff Probing for PMC Pm25LV010, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x80 0x00 0x00. probe_spi_rdid_generic: id1 0x80, id2 0x00 Probing for PMC Pm25LV016B, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x00 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x00 Probing for PMC Pm25LV020, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x08 0x7d. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x87d Probing for PMC Pm25LV040, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x00 0xf8. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xf8 Probing for PMC Pm25LV080B, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xbe 0x00 0x87. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xbe, id2 0x87 Probing for PMC Pm25LV512, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xe1 0x7d 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xe1, id2 0x7d00 Probing for Sanyo LF25FW203A, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x08 0x00 0x00. probe_spi_rdid_generic: id1 0x08, id2 0x00 Probing for Spansion S25FL004A, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xf0 0x00 0x0c. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xf0, id2 0x0c Probing for Spansion S25FL008A, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x90 0x00 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x90, id2 0xff Probing for Spansion S25FL016A, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x40 0x80. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x4080 Probing for Spansion S25FL032A, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x01 0x0f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x10f Probing for Spansion S25FL064A, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xf0 0x7f 0x1f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xf0, id2 0x7f1f Probing for SST SST25LF040A, 512 kB: serprog_spi_send_command, writecnt=4, readcnt=2 RES returned 0xcf 0x00. probe_spi_res2: id1 0xcf, id2 0x0 Probing for SST SST25LF080A, 1024 kB: serprog_spi_send_command, writecnt=4, readcnt=2 RES returned 0xf2 0x00. probe_spi_res2: id1 0xf2, id2 0x0 Probing for SST SST25VF010, 128 kB: serprog_spi_send_command, writecnt=4, readcnt=2 REMS returned 0x00 0x3f. probe_spi_rems: id1 0x0, id2 0x3f Probing for SST SST25VF016B, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x78 0x00 0xfc. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x78, id2 0xfc Probing for SST SST25VF032B, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x06 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x600 Probing for SST SST25VF064C, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x83 0x80. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x8380 Probing for SST SST25VF040, 512 kB: serprog_spi_send_command, writecnt=4, readcnt=2 REMS returned 0xff 0xc0. probe_spi_rems: id1 0xff, id2 0xc0 Probing for SST SST25VF040B, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0xfc 0x7f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0xfc7f Probing for SST SST25VF040B.REMS, 512 kB: serprog_spi_send_command, writecnt=4, readcnt=2 REMS returned 0x17 0xfc. probe_spi_rems: id1 0x17, id2 0xfc Probing for SST SST25VF080B, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x70 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x70ff Probing for ST M25P05-A, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x0f 0x02. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0xf02 Probing for ST M25P05, 64 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x10 0x08 0x20. Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xec 0x08. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xec08 Probing for ST M25P10, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xbe 0x00 0x82. Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x7d 0x02. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x7d02 Probing for ST M25P40, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x01 0x00 0x37. probe_spi_rdid_generic: id1 0x01, id2 0x37 Probing for ST M25P40-old, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x04 0x00 0x0f. Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xe1 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xe1ff Probing for ST M25P16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xc0 0x7f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xc07f Probing for ST M25P32, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x02 0xff 0x00. probe_spi_rdid_generic: id1 0x02, id2 0xff00 Probing for ST M25P64, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x00 0x81. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x81 Probing for ST M25P128, 16384 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x0f 0x00 0x01. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x0f, id2 0x01 Probing for ST M25PX16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x81 0xfe 0x02. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x81, id2 0xfe02 Probing for ST M25PX32, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x00 0x90. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x90 Probing for ST M25PX64, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x04 0x3f 0x80. probe_spi_rdid_generic: id1 0x04, id2 0x3f80 Probing for Winbond W25Q80, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xe0 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xe000 Probing for Winbond W25Q16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0xc0 0xc0. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0xc0c0 Probing for Winbond W25Q32, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x1f 0x80 0xff. probe_spi_rdid_generic: id1 0x1f, id2 0x80ff Probing for Winbond W25Q64, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x7f 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x7f00 Probing for Winbond W25Q128, 16384 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x1f 0xc2 0xe8. probe_spi_rdid_generic: id1 0x1f, id2 0xc2e8 Probing for Winbond W25X10, 128 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xff 0x01 0x3f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xff, id2 0x13f Probing for Winbond W25X20, 256 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xc0 0x00 0xff. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xc0, id2 0xff Probing for Winbond W25X40, 512 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x3f 0x00 0x40. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x3f, id2 0x40 Probing for Winbond W25X80, 1024 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0xff 0x0c. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0xff0c Probing for Winbond W25X16, 2048 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x3f 0x00 0x81. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x3f, id2 0x81 Probing for Winbond W25X32, 4096 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x7d 0x1f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x7d1f Probing for Winbond W25X64, 8192 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x04 0x00 0x0c. probe_spi_rdid_generic: id1 0x04, id2 0x0c Probing for Unknown SFDP-capable chip, 0 kB: spi_sfdp_read_sfdp_chunk: addr=0x0, len=2, data: serprog_spi_send_command, writecnt=4, readcnt=3 0x00 0xf8 spi_sfdp_read_sfdp_chunk: addr=0x2, len=2, data: serprog_spi_send_command, writecnt=4, readcnt=3 0x00 0xf8 Signature = 0xf800f800 (should be 0x50444653) No SFDP signature found. Probing for AMIC unknown AMIC SPI chip, 0 kB: serprog_spi_send_command, writecnt=1, readcnt=4 RDID returned 0xc2 0xdf 0x00 0xe0. probe_spi_rdid_generic: id1 0xc2, id2 0xdf00 Probing for Atmel unknown Atmel SPI chip, 0 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x41 0x00 0x03. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x41, id2 0x03 Probing for Eon unknown Eon SPI chip, 0 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xe0 0x00 0x7d. probe_spi_rdid_generic: id1 0xe0, id2 0x7d Probing for Macronix unknown Macronix SPI chip, 0 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x8c 0x00 0x80. probe_spi_rdid_generic: id1 0x8c, id2 0x80 Probing for PMC unknown PMC SPI chip, 0 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x04 0x00. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x400 Probing for SST unknown SST SPI chip, 0 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0xbe 0x00 0x2f. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0xbe, id2 0x2f Probing for ST unknown ST SPI chip, 0 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x00 0x42 0xc0. RDID byte 0 parity violation. probe_spi_rdid_generic: id1 0x00, id2 0x42c0 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x07 0x20 0x01. probe_spi_rdid_generic: id1 0x07, id2 0x2001 Probing for Generic unknown SPI chip (RDID), 0 kB: serprog_spi_send_command, writecnt=1, readcnt=3 RDID returned 0x79 0x10 0x0f. probe_spi_rdid_generic: id1 0x79, id2 0x100f Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI) on serprog. Probing for Generic unknown SPI chip (REMS), 0 kB: serprog_spi_send_command, writecnt=4, readcnt=2 REMS returned 0x17 0x10. probe_spi_rems: id1 0x17, id2 0x10 Found Generic flash chip "unknown SPI chip (RDID)" (0 kB, SPI). === This flash part has status NOT WORKING for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -VE, -Vw), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! No operations were specified. serprog_shutdown

1 0

Re: [flashrom] [PATCH] Make strnlen() visible in old versions of glibc.
by Carl-Daniel Hailfinger Jan. 27, 2015

Jan. 27, 2015

On 27.01.2015 00:53, Stefan Tauner wrote: > strnlen() is in POSIX 2008 but was a GNU extension up to glibc 2.10 requiring > to define _GNU_SOURCE. This fixes compilation on CentOS 4.9. > Also, move our implementation of strnlen() that was added to support DJGPP > to helpers.c. > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Excellent! Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Regards, Carl-Daniel

2 1

[commit] r1878 - trunk
by repository service Jan. 27, 2015

Jan. 27, 2015

Author: stefanct Date: Tue Jan 27 19:07:50 2015 New Revision: 1878 URL: http://flashrom.org/trac/flashrom/changeset/1878 Log: Make strnlen() visible in old versions of glibc. strnlen() is in POSIX 2008 but was a GNU extension up to glibc 2.10 requiring to define _GNU_SOURCE. This fixes compilation on CentOS 4.9. Also, move our implementation of strnlen() that was added to support DJGPP to helpers.c. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/dmi.c trunk/flash.h trunk/helpers.c Modified: trunk/dmi.c ============================================================================== --- trunk/dmi.c Mon Jan 26 23:06:04 2015 (r1877) +++ trunk/dmi.c Tue Jan 27 19:07:50 2015 (r1878) @@ -21,6 +21,13 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ +/* strnlen is in POSIX but was a GNU extension up to glibc 2.10 */ +#if (__GLIBC__ == 2 && __GLIBC_MINOR__ < 10) || __GLIBC__ < 2 +#define _GNU_SOURCE +#else +#define _POSIX_C_SOURCE 200809L +#endif + #include <strings.h> #include <string.h> #include <ctype.h> @@ -86,16 +93,6 @@ }; #if CONFIG_INTERNAL_DMI == 1 -#ifdef __DJGPP__ /* There is no strnlen in DJGPP. FIXME: Move this to a common utility file. */ -size_t strnlen(const char *str, size_t n) -{ - size_t i; - for (i = 0; i < n && str[i] != '\0'; i++) - ; - return i; -} -#endif - static bool dmi_checksum(const uint8_t * const buf, size_t len) { uint8_t sum = 0; Modified: trunk/flash.h ============================================================================== --- trunk/flash.h Mon Jan 26 23:06:04 2015 (r1877) +++ trunk/flash.h Tue Jan 27 19:07:50 2015 (r1878) @@ -260,6 +260,9 @@ #ifdef __MINGW32__ char* strtok_r(char *str, const char *delim, char **nextp); #endif +#if defined(__DJGPP__) +size_t strnlen(const char *str, size_t n); +#endif /* flashrom.c */ extern const char flashrom_version[]; Modified: trunk/helpers.c ============================================================================== --- trunk/helpers.c Mon Jan 26 23:06:04 2015 (r1877) +++ trunk/helpers.c Tue Jan 27 19:07:50 2015 (r1878) @@ -91,3 +91,13 @@ } #endif +/* There is no strnlen in DJGPP */ +#if defined(__DJGPP__) +size_t strnlen(const char *str, size_t n) +{ + size_t i; + for (i = 0; i < n && str[i] != '\0'; i++) + ; + return i; +} +#endif

1 0

[PATCH] Make strnlen() visible in old versions of glibc.
by Stefan Tauner Jan. 26, 2015

Jan. 26, 2015

strnlen() is in POSIX 2008 but was a GNU extension up to glibc 2.10 requiring to define _GNU_SOURCE. This fixes compilation on CentOS 4.9. Also, move our implementation of strnlen() that was added to support DJGPP to helpers.c. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> --- dmi.c | 17 +++++++---------- flash.h | 3 +++ helpers.c | 10 ++++++++++ 3 files changed, 20 insertions(+), 10 deletions(-) diff --git a/dmi.c b/dmi.c index 832d7ab..c9d904b 100644 --- a/dmi.c +++ b/dmi.c @@ -21,6 +21,13 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ +/* strnlen is in POSIX but was a GNU extension up to glibc 2.10 */ +#if (__GLIBC__ == 2 && __GLIBC_MINOR__ < 10) || __GLIBC__ < 2 +#define _GNU_SOURCE +#else +#define _POSIX_C_SOURCE 200809L +#endif + #include <strings.h> #include <string.h> #include <ctype.h> @@ -86,16 +93,6 @@ static const struct { }; #if CONFIG_INTERNAL_DMI == 1 -#ifdef __DJGPP__ /* There is no strnlen in DJGPP. FIXME: Move this to a common utility file. */ -size_t strnlen(const char *str, size_t n) -{ - size_t i; - for (i = 0; i < n && str[i] != '\0'; i++) - ; - return i; -} -#endif - static bool dmi_checksum(const uint8_t * const buf, size_t len) { uint8_t sum = 0; diff --git a/flash.h b/flash.h index 56d9e4b..5fb743d 100644 --- a/flash.h +++ b/flash.h @@ -260,6 +260,9 @@ void tolower_string(char *str); #ifdef __MINGW32__ char* strtok_r(char *str, const char *delim, char **nextp); #endif +#if defined(__DJGPP__) +size_t strnlen(const char *str, size_t n); +#endif /* flashrom.c */ extern const char flashrom_version[]; diff --git a/helpers.c b/helpers.c index 5685d29..7a146c3 100644 --- a/helpers.c +++ b/helpers.c @@ -91,3 +91,13 @@ char* strtok_r(char *str, const char *delim, char **nextp) } #endif +/* There is no strnlen in DJGPP */ +#if defined(__DJGPP__) +size_t strnlen(const char *str, size_t n) +{ + size_t i; + for (i = 0; i < n && str[i] != '\0'; i++) + ; + return i; +} +#endif -- Kind regards, Stefan Tauner

1 0

Re: [flashrom] [PATCH 3/3] Properly include libusb-win32 header.
by Carl-Daniel Hailfinger Jan. 26, 2015

Jan. 26, 2015

On 19.01.2015 21:39, Stefan Tauner wrote: > libusb-win32 is using a different header file name for a while, use > that on Windows builds to make clear that this is currently the > correct header to include. Yes, but at http://flashrom.org/Windows we still direct users to the old libusb-win32 version which uses the old usb.h. As long as those instructions are in the wiki, this will introduce additional breakage. > Hopefully this will change soonish with migrating away from libusb-0. > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > --- > Makefile | 5 +++++ > dediprog.c | 8 ++++++++ > 2 files changed, 13 insertions(+) > > diff --git a/Makefile b/Makefile > index 54ebfe4..03670d2 100644 > --- a/Makefile > +++ b/Makefile > @@ -843,7 +843,12 @@ endef > export LIBPCI_TEST > > define LIBUSB0_TEST > +#include "platform.h" > +#if IS_WINDOWS > +#include <lusb0_usb.h> > +#else > #include <usb.h> > +#endif > int main(int argc, char **argv) > { > (void) argc; We'd have to fix the wiki at the same time we commit this. Regards, Carl-Daniel

2 3

[commit] r1877 - trunk
by repository service Jan. 26, 2015

Jan. 26, 2015

Author: stefanct Date: Mon Jan 26 23:06:04 2015 New Revision: 1877 URL: http://flashrom.org/trac/flashrom/changeset/1877 Log: Properly include current libusb-win32 header. libusb-win32 is using a different header file name (lusb0_usb.h) for a while. Use that on Windows builds to make clear that this is currently the correct header to include. Hopefully this will change soonish by migrating away from libusb-0. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/Makefile trunk/dediprog.c Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Mon Jan 26 23:03:35 2015 (r1876) +++ trunk/Makefile Mon Jan 26 23:06:04 2015 (r1877) @@ -843,7 +843,12 @@ export LIBPCI_TEST define LIBUSB0_TEST +#include "platform.h" +#if IS_WINDOWS +#include <lusb0_usb.h> +#else #include <usb.h> +#endif int main(int argc, char **argv) { (void) argc; Modified: trunk/dediprog.c ============================================================================== --- trunk/dediprog.c Mon Jan 26 23:03:35 2015 (r1876) +++ trunk/dediprog.c Mon Jan 26 23:06:04 2015 (r1877) @@ -17,11 +17,19 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ +#include "platform.h" + #include <stdio.h> #include <string.h> #include <limits.h> #include <errno.h> + +#if IS_WINDOWS +#include <lusb0_usb.h> +#else #include <usb.h> +#endif + #include "flash.h" #include "chipdrivers.h" #include "programmer.h"

1 0

Re: [flashrom] [PATCH 1/3] Let pkg-config work with cross-compilers.
by Carl-Daniel Hailfinger Jan. 26, 2015

Jan. 26, 2015

On 19.01.2015 21:39, Stefan Tauner wrote: > In cross-compiler setups pkg-config often needs some help to > determine the correct libraries. This can be done for example by > setting PKG_CONFIG_LIBDIR to point to the directory where the > cross-compile .pc files are located. If PKG_CONFIG_LIBDIR was not > set already outside of the Makefile we set it according to LIBS_BASE > and add the respective path to the linker's rpath. This makes it > possible to easily cross-compile by only setting CC and LIBS_BASE on > the command line. > > This patch also removes the explicit default for LIBS_BASE again > because it does not play well with this change and was a bad idea to > begin with. > > Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> > Acked-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> My only worry is that we might break native compilation on some architectures where the buildbot currently only checks crossbuilding. Apart from that, the reasoning and the code looks good (though I'm not really an expert in linker behaviour). Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Regards, Carl-Daniel

2 1

[commit] r1876 - trunk
by repository service Jan. 26, 2015

Jan. 26, 2015

Author: stefanct Date: Mon Jan 26 23:03:35 2015 New Revision: 1876 URL: http://flashrom.org/trac/flashrom/changeset/1876 Log: Let pkg-config work with cross-compilers. In cross-compiler setups pkg-config often needs some help to determine the correct libraries. This can be done for example by setting PKG_CONFIG_LIBDIR to point to the directory where the cross-compile .pc files are located. If PKG_CONFIG_LIBDIR was not set already outside of the Makefile we set it according to LIBS_BASE and add the respective path to the linker's rpath. This makes it possible to easily cross-compile by only setting CC and LIBS_BASE on the command line. This patch also removes the explicit default for LIBS_BASE again because it does not play well with this change and was a bad idea to begin with. Signed-off-by: Stefan Tauner <stefan.tauner(a)alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/Makefile Modified: trunk/Makefile ============================================================================== --- trunk/Makefile Mon Jan 26 00:57:08 2015 (r1875) +++ trunk/Makefile Mon Jan 26 23:03:35 2015 (r1876) @@ -37,7 +37,6 @@ CFLAGS ?= -Os -Wall -Wshadow EXPORTDIR ?= . RANLIB ?= ranlib -LIBS_BASE ?= .. # The following parameter changes the default programmer that will be used if there is no -p/--programmer # argument given when running flashrom. The predefined setting does not enable any default so that every @@ -65,8 +64,11 @@ CFLAGS += -Werror endif +ifdef LIBS_BASE CPPFLAGS += -I$(LIBS_BASE)/include -LDFLAGS += -L$(LIBS_BASE)/lib +LDFLAGS += -L$(LIBS_BASE)/lib -Wl,-rpath -Wl,$(LIBS_BASE)/lib +PKG_CONFIG_LIBDIR ?= $(LIBS_BASE)/lib/pkgconfig +endif ############################################################################### # General OS-specific settings. @@ -613,7 +615,7 @@ endif ifeq ($(NEED_FTDI), yes) -FTDILIBS := $(shell pkg-config --libs libftdi 2>/dev/null || printf "%s" "-lftdi -lusb") +FTDILIBS := $(shell ([ -n "$(PKG_CONFIG_LIBDIR)" ] && export PKG_CONFIG_LIBDIR="$(PKG_CONFIG_LIBDIR)" ); pkg-config --libs libftdi || printf "%s" "-lftdi -lusb") FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "FT232H := yes" .features && printf "%s" "-D'HAVE_FT232H=1'") FEATURE_LIBS += $(shell LC_ALL=C grep -q "FTDISUPPORT := yes" .features && printf "%s" "$(FTDILIBS)") # We can't set NEED_USB here because that would transform libftdi auto-enabling @@ -736,7 +738,7 @@ ifeq ($(NEED_USB), yes) CHECK_LIBUSB0 = yes FEATURE_CFLAGS += -D'NEED_USB=1' -USBLIBS := $(shell pkg-config --libs libusb 2>/dev/null || printf "%s" "-lusb") +USBLIBS := $(shell ([ -n "$(PKG_CONFIG_LIBDIR)" ] && export PKG_CONFIG_LIBDIR="$(PKG_CONFIG_LIBDIR)" ); pkg-config --libs libusb || printf "%s" "-lusb") endif ifeq ($(CONFIG_PRINT_WIKI), yes)

1 0