February 2013 - flashrom - mail.coreboot.org

W836xx: 03RG89 Ver FAB1: flashrom -V
by Don Alexander Feb. 19, 2013

Feb. 19, 2013

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 flashrom -V flashrom v0.9.5.2-r1546 on Linux 3.2.0-4-amd64 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.7, GCC 4.6.2, little endian Command line (1 args): flashrom -V Calibrating delay loop... OS timer resolution is 1 usecs, 3013M loops per second, 10 myus = 10 us, 100 myus = 115 us, 1000 myus = 991 us, 10000 myus = 10179 us, 4 myus = 12 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Dell Inc. " DMI string system-product-name: "Dell System XPS L702X" DMI string system-version: "Not Specified" DMI string baseboard-manufacturer: "Dell Inc. " DMI string baseboard-product-name: "03RG89" DMI string baseboard-version: "FAB1" DMI string chassis-type: "Portable" Laptop detected via DMI. W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 85. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found ITE EC, ID 0x8518,Rev 0x02 on port 0x4e. ======================================================================== WARNING! You seem to be running flashrom on an unsupported laptop. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. If flash is shared with the EC, erase is guaranteed to brick your laptop and write may brick your laptop. Read and probe may irritate your EC and cause fan failure, backlight failure and sudden poweroff. You have been warned. ======================================================================== Aborting. - -- == Don Alexander It's a tough job, but some mug has to do it... RooSoft Ltd -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.12 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/ iEYEARECAAYFAlEi94cACgkQuipFNInZ6evyAACfWpcUW59YjP9xWE8uAttNQvw/ HP0AnRo5JGXUL4+mCVBRea2W861GexUh =H5wR -----END PGP SIGNATURE-----

1 0

Re: [flashrom] Please send a verbose log
by Eric Feb. 18, 2013

Feb. 18, 2013

Hi, Here is a verbose log for this : http://fr.asus.com/Motherboards/Intel_Socket_1155/P8P67M_PRO -- Si tu as une pomme, que j'ai une pomme, et que l'on échange nos pommes, nous aurons chacun une pomme. Mais si tu as une idée, que j'ai une idée, et que l'on échange nos idées, nous aurons chacun deux idées. La différence entre Linux et Windows ,c'est que Linux c'est comme une belle fille , il faut l'apprivoiser , la comprendre , la séduire tandis que Windows , c'est comme une prostitué , il faut payer et surtout bien se protéger. Pour remédier à ce problème, la solution c'est Ubuntu ! C'est une distribution GNU/Linux qui remplace avantageusement Ouinedoze. Vous êtes libre d'en obtenir une copie pour installation et utilisation en la téléchargeant gratuitement et légalement sur le lien ci-dessous. http://www.ubuntu-fr.org/telechargement

1 0

Re: [flashrom] Bypassing the size check
by Stefan Tauner Feb. 15, 2013

Feb. 15, 2013

On Thu, 14 Feb 2013 21:55:50 -0800 Jason Craik <jason.c7(a)gmail.com> wrote: > Hello, > > I'm trying to downgrade the bios on my Asus P8Z77-v LK motherboard and am > using a dos version of your program to try and do it. When I try and > reflash with the old .rom file it gives me an error about having two > different size files. I'm wondering if theres a way to just bypass that > check and force write the old .rom file onto the chip. Hello Jason, there is no command line switch to do this and there is no reason to do this in any sane use case either. How did you obtain the "old .rom file"? Obviously not by reading it with flashrom because then it would have the correct size. Also, P8Z77 sounds like a locked down board... please send a verbose log. I assume you have obtained an image of *the BIOS region only* by other means and want to write it to *the BIOS region only*... if you really know what you are doing, please take a look at the documentation of the layout file in the manpage and think about how you want to recover if something goes wrong. ;) -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Bypassing the size check
by Jason Craik Feb. 15, 2013

Feb. 15, 2013

Hello, I'm trying to downgrade the bios on my Asus P8Z77-v LK motherboard and am using a dos version of your program to try and do it. When I try and reflash with the old .rom file it gives me an error about having two different size files. I'm wondering if theres a way to just bypass that check and force write the old .rom file onto the chip. Thanks, Jason

1 0

flashrom for msi windpad 110w
by Seryi Kuznecov Feb. 13, 2013

Feb. 13, 2013

Hello! Need help knowing people. I have a tablet msi windpad 110w. For the Russian version of the producers put the trimmed version of the BIOS 207 http://paste.flashrom.org/view.php?id=1546 Roll back the standard means to version http://paste.flashrom.org/view.php?id=1547 by means ami msi and fails. The manufacturer says this to the fact that Russia banned TPM and therefore prohibited rollback bios and opening functions TPM (how unknown function in the BIOS to unlock the rollback not). The only way this is just the firmware programmer. It remains the last hope of flashrom. Here is a screen chip: http://paste.flashrom.org/view.php?id=1548. Datasheet: http://paste.flashrom.org/view.php?id=1549 Our version looks like 8-pin SOP (200mil, 150mil). Please help. Thank you.

1 0

Windpad 110w and flashrom
by Seryi Kuznecov Feb. 13, 2013

Feb. 13, 2013

Здравствуйте! Нужна помощь знающих людей. У меня планшет msi windpad 110w. Для российской версии производители поставили обрезанную версию биоса 207 http://paste.flashrom.org/view.php?id=1546 Откатить стандартными средствами на версию http://paste.flashrom.org/view.php?id=1547 с помощью средств ami и msi не получается. Производитель комментирует это тем, что в России запрещен TPM и поэтому запрещен откат биоса и открытие функций TPM (каким образом неизвестно, функции разлочки отката в биосе нет) . Единственный способ прошивки это только программатор. Остается последняя надежда на flashrom. Вот скрин чипа: http://paste.flashrom.org/view.php?id=1548. Даташит: http://paste.flashrom.org/view.php?id=1549 Наша версия похоже 8-pin SOP (200mil, 150mil). Прошу помощи. Спасибо.

1 0

[PATCH] total Makefile rewrite
by Carl-Daniel Hailfinger Feb. 13, 2013

Feb. 13, 2013

I almost lost my sanity trying to beat the Makefile into submission without using features only available in new GNU make versions. Some functions are now outsourced to a shell script. In theory, things should still work (except a few hardcoded dependencies which will be changed into autodetections in the future). At least now we have a framework to handle autodetection. It's not really hooked up yet, but it will allow stuff like make config CONFIG_WHATEVER=auto CONFIG_FOO=yes CONFIG_BAR=no The new (TM) way to compile flashrom is: make config make Please run "make distclean" the first time you test this patch. Not for merge yet, but this mechanism at least will allow clean handling of FTDI autodetect, libusb 1.x requirements and all that other pending fun stuff. Comments about the shell script are very appreciated, I tried to write in POSIX sh. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-Makefile_harddependencies_soft/hwaccess.h =================================================================== --- flashrom-Makefile_harddependencies_soft/hwaccess.h (Revision 1645) +++ flashrom-Makefile_harddependencies_soft/hwaccess.h (Arbeitskopie) @@ -167,7 +167,7 @@ #define le_to_cpu32 cpu_to_le32 #define le_to_cpu64 cpu_to_le64 -#if NEED_PCI == 1 +#if (NEED_PCI == 1) || (NEED_IOPORT_ACCESS == 1) #if defined (__i386__) || defined (__x86_64__) #define __FLASHROM_HAVE_OUTB__ 1 Index: flashrom-Makefile_harddependencies_soft/Makefile =================================================================== --- flashrom-Makefile_harddependencies_soft/Makefile (Revision 1645) +++ flashrom-Makefile_harddependencies_soft/Makefile (Arbeitskopie) @@ -103,28 +103,28 @@ LIBS += ../libgetopt/libgetopt.a # Bus Pirate, Serprog and PonyProg are not supported under DOS (missing serial support). ifeq ($(CONFIG_BUSPIRATE_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_BUSPIRATE_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_BUSPIRATE_SPI else override CONFIG_BUSPIRATE_SPI = no endif ifeq ($(CONFIG_SERPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_SERPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SERPROG else override CONFIG_SERPROG = no endif ifeq ($(CONFIG_PONY_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_PONY_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_PONY_SPI else override CONFIG_PONY_SPI = no endif # Dediprog and FT2232 are not supported under DOS (missing USB support). ifeq ($(CONFIG_DEDIPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_DEDIPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_DEDIPROG else override CONFIG_DEDIPROG = no endif ifeq ($(CONFIG_FT2232_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_FT2232_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_FT2232_SPI else override CONFIG_FT2232_SPI = no endif @@ -140,73 +140,73 @@ LDFLAGS += -L/usr/local/lib # Serprog is not supported under Windows/MinGW (missing sockets support). ifeq ($(CONFIG_SERPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_SERPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SERPROG else override CONFIG_SERPROG = no endif # For now we disable all PCI-based programmers on Windows/MinGW (no libpci). ifeq ($(CONFIG_INTERNAL), yes) -UNSUPPORTED_FEATURES += CONFIG_INTERNAL=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_INTERNAL else override CONFIG_INTERNAL = no endif ifeq ($(CONFIG_RAYER_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_RAYER_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_RAYER_SPI else override CONFIG_RAYER_SPI = no endif ifeq ($(CONFIG_NIC3COM), yes) -UNSUPPORTED_FEATURES += CONFIG_NIC3COM=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NIC3COM else override CONFIG_NIC3COM = no endif ifeq ($(CONFIG_GFXNVIDIA), yes) -UNSUPPORTED_FEATURES += CONFIG_GFXNVIDIA=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_GFXNVIDIA else override CONFIG_GFXNVIDIA = no endif ifeq ($(CONFIG_SATASII), yes) -UNSUPPORTED_FEATURES += CONFIG_SATASII=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SATASII else override CONFIG_SATASII = no endif ifeq ($(CONFIG_ATAHPT), yes) -UNSUPPORTED_FEATURES += CONFIG_ATAHPT=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_ATAHPT else override CONFIG_ATAHPT = no endif ifeq ($(CONFIG_DRKAISER), yes) -UNSUPPORTED_FEATURES += CONFIG_DRKAISER=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_DRKAISER else override CONFIG_DRKAISER = no endif ifeq ($(CONFIG_NICREALTEK), yes) -UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICREALTEK else override CONFIG_NICREALTEK = no endif ifeq ($(CONFIG_NICNATSEMI), yes) -UNSUPPORTED_FEATURES += CONFIG_NICNATSEMI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICNATSEMI else override CONFIG_NICNATSEMI = no endif ifeq ($(CONFIG_NICINTEL), yes) -UNSUPPORTED_FEATURES += CONFIG_NICINTEL=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICINTEL else override CONFIG_NICINTEL = no endif ifeq ($(CONFIG_NICINTEL_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_NICINTEL_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICINTEL_SPI else override CONFIG_NICINTEL_SPI = no endif ifeq ($(CONFIG_OGP_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_OGP_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_OGP_SPI else override CONFIG_OGP_SPI = no endif ifeq ($(CONFIG_SATAMV), yes) -UNSUPPORTED_FEATURES += CONFIG_SATAMV=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SATAMV else override CONFIG_SATAMV = no endif @@ -215,28 +215,28 @@ ifeq ($(TARGET_OS), libpayload) FLASHROM_CFLAGS += -DSTANDALONE ifeq ($(CONFIG_DUMMY), yes) -UNSUPPORTED_FEATURES += CONFIG_DUMMY=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_DUMMY else override CONFIG_DUMMY = no endif ifeq ($(CONFIG_BUSPIRATE_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_BUSPIRATE_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_BUSPIRATE_SPI else override CONFIG_BUSPIRATE_SPI = no endif ifeq ($(CONFIG_SERPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_SERPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SERPROG else override CONFIG_SERPROG = no endif # Dediprog and FT2232 are not supported with libpayload (missing libusb support) ifeq ($(CONFIG_DEDIPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_DEDIPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_DEDIPROG else override CONFIG_DEDIPROG = no endif ifeq ($(CONFIG_FT2232_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_FT2232_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_FT2232_SPI else override CONFIG_FT2232_SPI = no endif @@ -244,7 +244,7 @@ ifneq ($(TARGET_OS), Linux) ifeq ($(CONFIG_LINUX_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_LINUX_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_LINUX_SPI else override CONFIG_LINUX_SPI = no endif @@ -260,32 +260,32 @@ # Right now this means the drivers below only work on x86. ifneq ($(ARCH), x86) ifeq ($(CONFIG_NIC3COM), yes) -UNSUPPORTED_FEATURES += CONFIG_NIC3COM=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NIC3COM else override CONFIG_NIC3COM = no endif ifeq ($(CONFIG_NICREALTEK), yes) -UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICREALTEK else override CONFIG_NICREALTEK = no endif ifeq ($(CONFIG_NICNATSEMI), yes) -UNSUPPORTED_FEATURES += CONFIG_NICNATSEMI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICNATSEMI else override CONFIG_NICNATSEMI = no endif ifeq ($(CONFIG_RAYER_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_RAYER_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_RAYER_SPI else override CONFIG_RAYER_SPI = no endif ifeq ($(CONFIG_ATAHPT), yes) -UNSUPPORTED_FEATURES += CONFIG_ATAHPT=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_ATAHPT else override CONFIG_ATAHPT = no endif ifeq ($(CONFIG_SATAMV), yes) -UNSUPPORTED_FEATURES += CONFIG_SATAMV=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SATAMV else override CONFIG_SATAMV = no endif @@ -411,6 +411,128 @@ ############################################################################### # Programmer drivers and programmer support infrastructure. +ifeq ($(CONFIG_INTERNAL), yes) +NEED_PCI += CONFIG_INTERNAL +endif + +ifeq ($(CONFIG_SERPROG), yes) +NEED_SERIAL += CONFIG_SERPROG +NEED_NET += CONFIG_SERPROG +endif + +ifeq ($(CONFIG_RAYER_SPI), yes) +NEED_IOPORT_ACCESS += CONFIG_RAYER_SPI +endif + +ifeq ($(CONFIG_PONY_SPI), yes) +NEED_SERIAL += CONFIG_PONY_SPI +endif + +ifeq ($(CONFIG_BITBANG_SPI), yes) +endif + +ifeq ($(CONFIG_NIC3COM), yes) +NEED_PCI += CONFIG_NIC3COM +endif + +ifeq ($(CONFIG_GFXNVIDIA), yes) +NEED_PCI += CONFIG_GFXNVIDIA +endif + +ifeq ($(CONFIG_SATASII), yes) +NEED_PCI += CONFIG_SATASII +endif + +ifeq ($(CONFIG_ATAHPT), yes) +NEED_PCI += CONFIG_ATAHPT +endif + +ifeq ($(CONFIG_FT2232_SPI), yes) +NEED_FTDI += CONFIG_FT2232_SPI +endif + +ifeq ($(CONFIG_DUMMY), yes) +endif + +ifeq ($(CONFIG_DRKAISER), yes) +NEED_PCI += CONFIG_DRKAISER +endif + +ifeq ($(CONFIG_NICREALTEK), yes) +NEED_PCI += CONFIG_NICREALTEK +endif + +ifeq ($(CONFIG_NICNATSEMI), yes) +NEED_PCI += CONFIG_NICNATSEMI +endif + +ifeq ($(CONFIG_NICINTEL), yes) +NEED_PCI += CONFIG_NICINTEL +endif + +ifeq ($(CONFIG_NICINTEL_SPI), yes) +NEED_PCI += CONFIG_NICINTEL_SPI +endif + +ifeq ($(CONFIG_OGP_SPI), yes) +NEED_PCI += CONFIG_OGP_SPI +endif + +ifeq ($(CONFIG_BUSPIRATE_SPI), yes) +NEED_SERIAL += CONFIG_BUSPIRATE_SPI +endif + +ifeq ($(CONFIG_DEDIPROG), yes) +NEED_USB += CONFIG_DEDIPROG +endif + +ifeq ($(CONFIG_SATAMV), yes) +NEED_PCI += CONFIG_SATAMV +endif + +ifeq ($(CONFIG_LINUX_SPI), yes) +endif + +ifneq ($(NEED_SERIAL), ) +endif + +ifneq ($(NEED_NET), ) +endif + +ifneq ($(NEED_PCI), ) +CHECK_LIBPCI = yes +endif + +ifneq ($(NEED_USB), ) +CHECK_LIBUSB0 = yes +endif + +ifneq ($(NEED_FTDI), ) +CHECK_LIBFTDI = yes +endif + +############################################################################################################################################################################# + +defaulttarget: all + +config: compiler + @printf "" > .availablefeatures + @./config.sh utsname +ifneq ($(CHECK_LIBPCI), ) + @./config.sh libpci +endif +ifneq ($(CHECK_LIBUSB0), ) + @./config.sh libusb0 +endif +ifeq ($(CHECK_LIBFTDI), yes) + @./config.sh libftdi +endif +ifeq ($(CONFIG_LINUX_SPI), yes) + @./config.sh linuxspi +endif + +-include .availablefeatures + FEATURE_CFLAGS += -D'CONFIG_DEFAULT_PROGRAMMER=$(CONFIG_DEFAULT_PROGRAMMER)' ifeq ($(CONFIG_INTERNAL), yes) @@ -421,27 +543,21 @@ PROGRAMMER_OBJS += ichspi.o ich_descriptors.o else endif -NEED_PCI := yes endif ifeq ($(CONFIG_SERPROG), yes) FEATURE_CFLAGS += -D'CONFIG_SERPROG=1' PROGRAMMER_OBJS += serprog.o -NEED_SERIAL := yes -NEED_NET := yes endif ifeq ($(CONFIG_RAYER_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_RAYER_SPI=1' PROGRAMMER_OBJS += rayer_spi.o -# Actually, NEED_PCI is wrong. NEED_IOPORT_ACCESS would be more correct. -NEED_PCI := yes endif ifeq ($(CONFIG_PONY_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_PONY_SPI=1' PROGRAMMER_OBJS += pony_spi.o -NEED_SERIAL := yes endif ifeq ($(CONFIG_BITBANG_SPI), yes) @@ -452,36 +568,29 @@ ifeq ($(CONFIG_NIC3COM), yes) FEATURE_CFLAGS += -D'CONFIG_NIC3COM=1' PROGRAMMER_OBJS += nic3com.o -NEED_PCI := yes endif ifeq ($(CONFIG_GFXNVIDIA), yes) FEATURE_CFLAGS += -D'CONFIG_GFXNVIDIA=1' PROGRAMMER_OBJS += gfxnvidia.o -NEED_PCI := yes endif ifeq ($(CONFIG_SATASII), yes) FEATURE_CFLAGS += -D'CONFIG_SATASII=1' PROGRAMMER_OBJS += satasii.o -NEED_PCI := yes endif ifeq ($(CONFIG_ATAHPT), yes) FEATURE_CFLAGS += -D'CONFIG_ATAHPT=1' PROGRAMMER_OBJS += atahpt.o -NEED_PCI := yes endif ifeq ($(CONFIG_FT2232_SPI), yes) -FTDILIBS := $(shell pkg-config --libs libftdi 2>/dev/null || printf "%s" "-lftdi -lusb") -# This is a totally ugly hack. -FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "FTDISUPPORT := yes" .features && printf "%s" "-D'CONFIG_FT2232_SPI=1'") -FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "FT232H := yes" .features && printf "%s" "-D'HAVE_FT232H=1'") -FEATURE_LIBS += $(shell LC_ALL=C grep -q "FTDISUPPORT := yes" .features && printf "%s" "$(FTDILIBS)") +FEATURE_CFLAGS += -D'CONFIG_FT2232_SPI=1' +ifeq ($(FT232H), yes) +FEATURE_CFLAGS += -D'HAVE_FT232H=1' +endif PROGRAMMER_OBJS += ft2232_spi.o -# We can't set NEED_USB here because that would transform libftdi auto-enabling -# into a hard requirement for libusb, defeating the purpose of auto-enabling. endif ifeq ($(CONFIG_DUMMY), yes) @@ -492,75 +601,64 @@ ifeq ($(CONFIG_DRKAISER), yes) FEATURE_CFLAGS += -D'CONFIG_DRKAISER=1' PROGRAMMER_OBJS += drkaiser.o -NEED_PCI := yes endif ifeq ($(CONFIG_NICREALTEK), yes) FEATURE_CFLAGS += -D'CONFIG_NICREALTEK=1' PROGRAMMER_OBJS += nicrealtek.o -NEED_PCI := yes endif ifeq ($(CONFIG_NICNATSEMI), yes) FEATURE_CFLAGS += -D'CONFIG_NICNATSEMI=1' PROGRAMMER_OBJS += nicnatsemi.o -NEED_PCI := yes endif ifeq ($(CONFIG_NICINTEL), yes) FEATURE_CFLAGS += -D'CONFIG_NICINTEL=1' PROGRAMMER_OBJS += nicintel.o -NEED_PCI := yes endif ifeq ($(CONFIG_NICINTEL_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_NICINTEL_SPI=1' PROGRAMMER_OBJS += nicintel_spi.o -NEED_PCI := yes endif ifeq ($(CONFIG_OGP_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_OGP_SPI=1' PROGRAMMER_OBJS += ogp_spi.o -NEED_PCI := yes endif ifeq ($(CONFIG_BUSPIRATE_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_BUSPIRATE_SPI=1' PROGRAMMER_OBJS += buspirate_spi.o -NEED_SERIAL := yes endif ifeq ($(CONFIG_DEDIPROG), yes) FEATURE_CFLAGS += -D'CONFIG_DEDIPROG=1' PROGRAMMER_OBJS += dediprog.o -NEED_USB := yes endif ifeq ($(CONFIG_SATAMV), yes) FEATURE_CFLAGS += -D'CONFIG_SATAMV=1' PROGRAMMER_OBJS += satamv.o -NEED_PCI := yes endif ifeq ($(CONFIG_LINUX_SPI), yes) -# This is a totally ugly hack. -FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "LINUX_SPI_SUPPORT := yes" .features && printf "%s" "-D'CONFIG_LINUX_SPI=1'") +FEATURE_CFLAGS += -D'CONFIG_LINUX_SPI=1' PROGRAMMER_OBJS += linux_spi.o endif -ifeq ($(NEED_SERIAL), yes) +ifneq ($(NEED_SERIAL), ) LIB_OBJS += serial.o endif -ifeq ($(NEED_NET), yes) +ifneq ($(NEED_NET), ) ifeq ($(TARGET_OS), SunOS) LIBS += -lsocket endif endif -ifeq ($(NEED_PCI), yes) -CHECK_LIBPCI = yes +ifneq ($(NEED_PCI), ) FEATURE_CFLAGS += -D'NEED_PCI=1' PROGRAMMER_OBJS += pcidev.o physmap.o hwaccess.o ifeq ($(TARGET_OS), NetBSD) @@ -589,32 +687,45 @@ endif endif -ifeq ($(NEED_USB), yes) -CHECK_LIBUSB0 = yes +ifneq ($(NEED_USB), ) FEATURE_CFLAGS += -D'NEED_USB=1' USBLIBS := $(shell pkg-config --libs libusb 2>/dev/null || printf "%s" "-lusb") endif +ifneq ($(NEED_FTDI), ) +FEATURE_CFLAGS += -D'NEED_FTDI=1' +FTDILIBS := $(shell pkg-config --libs libftdi 2>/dev/null || libftdi-config --libs 2>/dev/null || printf "%s" "-lftdi") +endif + +ifneq ($(NEED_IOPORT_ACCESS), ) +FEATURE_CFLAGS += -D'NEED_IOPORT_ACCESS=1' +PROGRAMMER_OBJS += hwaccess.o +endif + ifeq ($(CONFIG_PRINT_WIKI), yes) FEATURE_CFLAGS += -D'CONFIG_PRINT_WIKI=1' CLI_OBJS += print_wiki.o endif -FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "UTSNAME := yes" .features && printf "%s" "-D'HAVE_UTSNAME=1'") +ifeq ($(UTSNAME), yes) +FEATURE_CFLAGS += -D'HAVE_UTSNAME=1' +endif # We could use PULLED_IN_LIBS, but that would be ugly. -FEATURE_LIBS += $(shell LC_ALL=C grep -q "NEEDLIBZ := yes" .libdeps && printf "%s" "-lz") +ifeq ($(NEEDLIBZ), yes) +FEATURE_LIBS += -lz +endif -LIBFLASHROM_OBJS = $(CHIP_OBJS) $(PROGRAMMER_OBJS) $(LIB_OBJS) +LIBFLASHROM_OBJS = $(CHIP_OBJS) $(sort $(PROGRAMMER_OBJS)) $(LIB_OBJS) OBJS = $(CLI_OBJS) $(LIBFLASHROM_OBJS) -all: hwlibs features $(PROGRAM)$(EXEC_SUFFIX) +all: $(PROGRAM)$(EXEC_SUFFIX) ifeq ($(ARCH), x86) @+$(MAKE) -C util/ich_descriptors_tool/ TARGET_OS=$(TARGET_OS) EXEC_SUFFIX=$(EXEC_SUFFIX) endif $(PROGRAM)$(EXEC_SUFFIX): $(OBJS) - $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FEATURE_LIBS) $(LIBS) $(PCILIBS) $(USBLIBS) + $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FTDILIBS) $(USBLIBS) $(PCILIBS) $(FEATURE_LIBS) $(LIBS) libflashrom.a: $(LIBFLASHROM_OBJS) $(AR) rcs $@ $^ @@ -625,7 +736,11 @@ # stored files, they can be handled here as well. TAROPTIONS = $(shell LC_ALL=C tar --version|grep -q GNU && echo "--owner=root --group=root") -%.o: %.c .features +%.o: %.c +ifeq ($(wildcard .availablefeatures), ) + @echo 'You have to run "make config" first' + @false +endif $(CC) -MMD $(CFLAGS) $(CPPFLAGS) $(FLASHROM_CFLAGS) $(FEATURE_CFLAGS) $(SVNDEF) -o $@ -c $< # Make sure to add all names of generated binaries here. @@ -636,7 +751,7 @@ @+$(MAKE) -C util/ich_descriptors_tool/ clean distclean: clean - rm -f .features .libdeps + rm -f .availablefeatures strip: $(PROGRAM)$(EXEC_SUFFIX) $(STRIP) $(STRIP_ARGS) $(PROGRAM)$(EXEC_SUFFIX) @@ -699,60 +814,6 @@ endef export LIBUSB0_TEST -hwlibs: compiler - @printf "" > .libdeps -ifeq ($(CHECK_LIBPCI), yes) - @printf "Checking for libpci headers... " - @echo "$$LIBPCI_TEST" > .test.c - @$(CC) -c $(CPPFLAGS) $(CFLAGS) .test.c -o .test.o >/dev/null && \ - echo "found." || ( echo "not found."; echo; \ - echo "Please install libpci headers (package pciutils-devel)."; \ - echo "See README for more information."; echo; \ - rm -f .test.c .test.o; exit 1) - @printf "Checking if libpci is present and sufficient... " - @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) $(PCILIBS) >/dev/null && \ - echo "yes." || ( echo "no."; \ - printf "Checking if libz+libpci are present and sufficient..."; \ - $(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) $(PCILIBS) -lz >/dev/null && \ - ( echo "yes."; echo "NEEDLIBZ := yes" > .libdeps ) || ( echo "no."; echo; \ - echo "Please install libpci (package pciutils) and/or libz."; \ - echo "See README for more information."; echo; \ - rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) ) - @rm -f .test.c .test.o .test$(EXEC_SUFFIX) -endif -ifeq ($(CHECK_LIBUSB0), yes) - @printf "Checking for libusb-0.1/libusb-compat headers... " - @echo "$$LIBUSB0_TEST" > .test.c - @$(CC) -c $(CPPFLAGS) $(CFLAGS) .test.c -o .test.o >/dev/null && \ - echo "found." || ( echo "not found."; echo; \ - echo "Please install libusb-0.1 headers or libusb-compat headers."; \ - echo "See README for more information."; echo; \ - rm -f .test.c .test.o; exit 1) - @printf "Checking if libusb-0.1 is usable... " - @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) $(USBLIBS) >/dev/null && \ - echo "yes." || ( echo "no."; \ - echo "Please install libusb-0.1 or libusb-compat."; \ - echo "See README for more information."; echo; \ - rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) - @rm -f .test.c .test.o .test$(EXEC_SUFFIX) -endif - -.features: features - -# If a user does not explicitly request a non-working feature, we should -# silently disable it. However, if a non-working (does not compile) feature -# is explicitly requested, we should bail out with a descriptive error message. -# We also have to check that at least one programmer driver is enabled. -featuresavailable: -ifeq ($(PROGRAMMER_OBJS),) - @echo "You have to enable at least one programmer driver!" - @false -endif -ifneq ($(UNSUPPORTED_FEATURES), ) - @echo "The following features are unavailable on your machine: $(UNSUPPORTED_FEATURES)" - @false -endif - define FTDI_TEST #include <ftdi.h> struct ftdi_context *ftdic = NULL; @@ -771,60 +832,47 @@ endef export FTDI_232H_TEST -define UTSNAME_TEST -#include <sys/utsname.h> -struct utsname osinfo; +define LINUX_SPI_TEST +#include <linux/types.h> +#include <linux/spi/spidev.h> + int main(int argc, char **argv) { (void) argc; (void) argv; - uname (&osinfo); return 0; } endef -export UTSNAME_TEST +export LINUX_SPI_TEST -define LINUX_SPI_TEST -#include <linux/types.h> -#include <linux/spi/spidev.h> - +define UTSNAME_TEST +#include <sys/utsname.h> +struct utsname osinfo; int main(int argc, char **argv) { (void) argc; (void) argv; + uname (&osinfo); return 0; } endef -export LINUX_SPI_TEST +export UTSNAME_TEST -features: compiler - @echo "FEATURES := yes" > .features.tmp -ifeq ($(CONFIG_FT2232_SPI), yes) - @printf "Checking for FTDI support... " - @echo "$$FTDI_TEST" > .featuretest.c - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ - ( echo "found."; echo "FTDISUPPORT := yes" >> .features.tmp ) || \ - ( echo "not found."; echo "FTDISUPPORT := no" >> .features.tmp ) - @printf "Checking for FT232H support in libftdi... " - @echo "$$FTDI_232H_TEST" >> .featuretest.c - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ - ( echo "found."; echo "FT232H := yes" >> .features.tmp ) || \ - ( echo "not found."; echo "FT232H := no" >> .features.tmp ) +export CC + +# If a user does not explicitly request a non-working feature, we should +# silently disable it. However, if a non-working (does not compile) feature +# is explicitly requested, we should bail out with a descriptive error message. +# We also have to check that at least one programmer driver is enabled. +featuresavailable: +ifeq ($(PROGRAMMER_OBJS),) + @echo "You have to enable at least one programmer driver!" + @false endif -ifeq ($(CONFIG_LINUX_SPI), yes) - @printf "Checking if Linux SPI headers are present... " - @echo "$$LINUX_SPI_TEST" > .featuretest.c - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) >/dev/null 2>&1 && \ - ( echo "yes."; echo "LINUX_SPI_SUPPORT := yes" >> .features.tmp ) || \ - ( echo "no."; echo "LINUX_SPI_SUPPORT := no" >> .features.tmp ) +ifneq ($(UNSUPPORTED_TARGET_FEATURES), ) + @echo "The following features are unavailable on the target machine: $(UNSUPPORTED_TARGET_FEATURES)" + @false endif - @printf "Checking for utsname support... " - @echo "$$UTSNAME_TEST" > .featuretest.c - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) >/dev/null 2>&1 && \ - ( echo "found."; echo "UTSNAME := yes" >> .features.tmp ) || \ - ( echo "not found."; echo "UTSNAME := no" >> .features.tmp ) - @$(DIFF) -q .features.tmp .features >/dev/null 2>&1 && rm .features.tmp || mv .features.tmp .features - @rm -f .featuretest.c .featuretest$(EXEC_SUFFIX) install: $(PROGRAM)$(EXEC_SUFFIX) mkdir -p $(DESTDIR)$(PREFIX)/sbin @@ -849,6 +897,10 @@ libpayload: clean make CC="CC=i386-elf-gcc lpgcc" AR=i386-elf-ar RANLIB=i386-elf-ranlib -.PHONY: all clean distclean compiler hwlibs features export tarball dos featuresavailable +.PHONY: all clean distclean compiler config export tarball dos featuresavailable +.EXPORT_ALL_VARIABLES: + +-include .availablefeatures + -include $(OBJS:.o=.d) Index: flashrom-Makefile_harddependencies_soft/config.sh =================================================================== --- flashrom-Makefile_harddependencies_soft/config.sh (Revision 0) +++ flashrom-Makefile_harddependencies_soft/config.sh (Revision 0) @@ -0,0 +1,199 @@ +#!/bin/sh +libpci() { + printf "Checking for libpci headers... " + echo "$LIBPCI_TEST" > .test.c + ${CC} -c ${CPPFLAGS} ${CFLAGS} .test.c -o .test.o >.testresult 2>&1 && { + echo "found." + } || { + echo "not found." + if [ ${CHECK_LIBPCI} = yes ]; then + echo + echo "Please install libpci headers (package pciutils-devel)" + echo "or disable the following features: ${NEED_PCI}" + echo "See README for more information." + echo + rm -f .test.o + exit 1 + else + for a in ${NEED_PCI}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_PCI}" + echo "See README for more information." + echo + rm -f .test.c .test.o + return 0 + fi + } + printf "Checking if libpci is present and sufficient... " + ${CC} ${LDFLAGS} .test.o -o .test${EXEC_SUFFIX} ${PCILIBS} ${LIBS} >.testresult 2>&1 && { + echo "yes." + } || { + echo "no." + printf "Checking if libz+libpci are present and sufficient..." + ${CC} ${LDFLAGS} .test.o -o .test${EXEC_SUFFIX} ${PCILIBS} -lz ${LIBS} >.testresult 2>&1 && { + echo "yes." + echo "NEEDLIBZ := yes" > .availablefeatures + } || { + echo "no." + if [ ${CHECK_LIBPCI} = yes ]; then + echo + echo "Please install libpci (package pciutils) and/or libz" + echo "or disable the following features: ${NEED_PCI}" + echo "See README for more information." + echo + rm -f test.o .test${EXEC_SUFFIX} + exit 1 + else + for a in ${NEED_PCI}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_PCI}" + echo "See README for more information." + echo + rm -f .test.c .test.o; .test${EXEC_SUFFIX} + return 0 + fi + } + } + rm -f .test.c .test.o .test${EXEC_SUFFIX} .testresult +} + +libusb0() { + printf "Checking for libusb-0.1/libusb-compat headers... " + echo "$LIBUSB0_TEST" > .test.c + ${CC} -c ${CPPFLAGS} ${CFLAGS} .test.c -o .test.o >.testresult 2>&1 && { + echo "found." + } || { + echo "not found." + if [ ${CHECK_LIBUSB0} = yes ]; then + echo + echo "Please install libusb-0.1 headers or libusb-compat headers" + echo "or disable the following features: ${NEED_USB}" + echo "See README for more information." + echo + rm -f .test.o + exit 1 + else + for a in ${NEED_USB}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_USB}" + echo "See README for more information." + echo + rm -f .test.c .test.o + return 0 + fi + } + printf "Checking if libusb-0.1/libusb-compat is usable... " + ${CC} ${LDFLAGS} .test.o -o .test${EXEC_SUFFIX} ${USBLIBS} ${LIBS} >.testresult 2>&1 && { + echo "yes." + } || { + echo "no." + if [ ${CHECK_LIBUSB0} = yes ]; then + echo + echo "Please install libusb-0.1 or libusb-compat" + echo "or disable the following features: ${NEED_USB}" + echo "See README for more information." + echo + rm -f .test.o .test${EXEC_SUFFIX} + exit 1 + else + for a in ${NEED_USB}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_USB}" + echo "See README for more information." + echo + rm -f .test.c .test.o + return 0 + fi + } + rm -f .test.c .test.o .test${EXEC_SUFFIX} .testresult +} + +libftdi() { + printf "Checking for libftdi support... " + echo "$FTDI_TEST" > .test.c + ${CC} ${CPPFLAGS} ${CFLAGS} ${LDFLAGS} .test.c -o .test${EXEC_SUFFIX} ${FTDILIBS} ${LIBS} >.testresult 2>&1 && { + echo "found." + } || { + echo "not found." + if [ ${CHECK_LIBFTDI} = yes ]; then + echo + echo "Please install libftdi headers" + echo "or disable the following features: ${NEED_FTDI}" + echo "See README for more information." + echo + rm -f .test${EXEC_SUFFIX} + exit 1 + else + for a in ${NEED_FTDI}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_FTDI}" + echo "See README for more information." + echo + rm -f .test.c .test${EXEC_SUFFIX} + return 0 + fi + } + printf "Checking for FT232H support in libftdi... " + echo "$FTDI_232H_TEST" >> .test.c + ${CC} ${CPPFLAGS} ${CFLAGS} ${LDFLAGS} .test.c -o .test${EXEC_SUFFIX} ${FTDILIBS} ${LIBS} >.testresult 2>&1 && { + echo "found." + echo "FT232H := yes" >> .availablefeatures + } || { + echo "not found." + } + rm -f .test.c .test${EXEC_SUFFIX} .testresult +} + +linuxspi() { + printf "Checking for Linux kernel SPI headers... " + echo "$LINUX_SPI_TEST" > .test.c + ${CC} ${CPPFLAGS} ${CFLAGS} ${LDFLAGS} .test.c -o .test${EXEC_SUFFIX} >.testresult 2>&1 && { + echo "found." + } || { + echo "not found." + if [ ${CONFIG_LINUX_SPI} = yes ]; then + echo + echo "Please install Linux kernel SPI headers (linux/spi/spidev.h, part of recent glibc)" + echo "or disable the following features: CONFIG_LINUX_SPI" + echo "See README for more information." + echo + rm -f .test${EXEC_SUFFIX} + exit 1 + else + for a in CONFIG_LINUX_SPI; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: CONFIG_LINUX_SPI" + echo "See README for more information." + echo + rm -f .test.c .test${EXEC_SUFFIX} + return 0 + fi + } + rm -f .test.c .test${EXEC_SUFFIX} .testresult +} + +utsname() { + printf "Checking for utsname support... " + echo "$UTSNAME_TEST" > .test.c + ${CC} ${CPPFLAGS} ${CFLAGS} ${LDFLAGS} .test.c -o .test${EXEC_SUFFIX} >/dev/null 2>&1 && { + echo "found." + echo "UTSNAME := yes" >> .availablefeatures + } || { + echo "not found." + } + rm -f .test.c .test${EXEC_SUFFIX} .testresult +} + +eval $1 Eigenschaftsänderungen: flashrom-Makefile_harddependencies_soft/config.sh ___________________________________________________________________ Hinzugefügt: svn:executable + * -- http://www.hailfinger.org/

1 1

Report: Intel DQ77KB KBQ7710H.86A.0049.2013.0130.1732 write
by dpcimanager＠users.sourceforge.net Feb. 12, 2013

Feb. 12, 2013

flashrom v0.9.6.1-r1646 on Darwin 12.2.0 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.10, LLVM Clang 4.1 ((tags/Apple/clang-421.11.66)), little endian Command line (5 args): /Volumes/USB/[Megafileupload]DPCIManager/DPCIManager.app/Contents/MacOS/flashrom -VV -w /var/folders/0g/vk1bx8k94r7_3_p_tllzvqvm0000gn/T/DPCIcw3meF.rom -p internal Calibrating delay loop... OS timer resolution is 1 usecs, 459M loops per second, 10 myus = 12 us, 100 myus = 102 us, 1000 myus = 1028 us, 10000 myus = 10668 us, 4 myus = 4 us, OK. Initializing internal programmer Mapping low megabyte at 0x00000400, unaligned size 0xffc00. Mapping low megabyte, 0xffc00 bytes at unaligned 0x00000400. No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "Intel Corporation" DMI string baseboard-product-name: "DQ77KB" DMI string baseboard-version: "AAG40294-401" DMI string chassis-type: "Desktop" Found chipset "Intel Q77" with PCI ID 8086:1e47. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes BIOS_CNTL = 0x2a: BIOS Lock Enable: enabled, BIOS Write Enable: disabled Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x0b on Q77 failed. New value is 0x2a. Root Complex Register Block address = 0xfed1c000 GCS = 0xc61: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 Warning: SPI Configuration Lockdown activated. Reading OPCODES... done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0x20, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x9f, read w/o addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x00, read w/o addr, none op[7]: 0x00, read w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x00 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00000000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x0bff05c0 FREG1: BIOS region (0x005c0000-0x00bfffff) is read-write. 0x5C: 0x05bf0003 FREG2: Warning: Management Engine region (0x00003000-0x005bffff) is locked. 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write. 0x64: 0x00001fff FREG4: Platform Data region is unused. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled for safety reasons. You can enforce write support with the ich_spi_force programmer option, but you will most likely harm your hardware! If you force flashrom you will get no support if something breaks. On a few mainboards it is possible to enable write access by setting a jumper (see its documentation or the board itself). 0x90: 0x80 (SSFS) SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0 0x91: 0xf94010 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=0, SME=0, SCF=1 0x94: 0x0006 (PREOP) 0x96: 0x043b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0000019f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x03040103 FLMAP1 0x12100206 FLMAP2 0x00210120 --- Details --- NR (Number of Regions): 4 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 2 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x0930001c FLILL 0x00000000 --- Details --- Component 1 density: 8 MB Component 2 density: 4 MB Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 33 MHz Write and Erase Clock Freq.: 33 MHz Fast Read is supported. Fast Read Clock Frequency: 33 MHz No forbidden opcodes. === Region Section === FLREG0 0x00000000 FLREG1 0x0bff05c0 FLREG2 0x05bf0003 FLREG3 0x00020001 FLREG4 0x00001fff --- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x005c0000 - 0x00bfffff Region 2 (ME ) 0x00003000 - 0x005bffff Region 3 (GbE ) 0x00001000 - 0x00002fff Region 4 (Platf.) is unused. === Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08080118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE rw Enabling hardware sequencing due to multiple flash chips detected. SPI Read Configuration: prefetching enabled, caching enabled, PROBLEMS, continuing anyway The following protocols are supported: FWH, Programmer-specific. Probing for Programmer Opaque flash chip, 0 kB: Found 2 attached SPI flash chips with a combined density of 12288 kB. There is only one partition containing the whole address space (0x000000 - 0xbfffff). There are 3072 erase blocks with 4096 B each. Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific) at physical address 0x0. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific). Write/erase is not working yet on your programmer in its current configuration. Aborting. Restoring MMIO space at 0x10ef718a0 Restoring PCI config space for 00:1f:0 reg 0xdc

1 0

Re: [flashrom] Fwd: BIOS Write Enable bit problem.
by Andrew Goodbody Feb. 11, 2013

Feb. 11, 2013

On 10/02/13 00:45, Rich Futyma wrote: > Would happen to know which linux driver handles this interrupt? SMM code is loaded into SMRAM during BIOS POST. Then the access to SMRAM is locked so that SMRAM is only visible when an SMI is active. The CPU cannot access SMRAM when no SMI is active. The CPU immediately starts to execute code from SMRAM once it receives the SMI. There is no Linux code involved, this is all initialised before any OS code is loaded. > Also, do you know where is this "correct handshake" described? It seems > that once bit 1 is set it can only be cleared by the reset. No. This handshake is not public knowledge AFAIK. It would not be much of a protection mechanism if everyone, including the virus writers, knew how to bypass it. I would expect the handshake to involve cryptography as well. Andrew

2 1

Re: [flashrom] a serious problem to solve
by Idwer Vollering Feb. 10, 2013

Feb. 10, 2013

2013/2/10 Henry Blanco Lores <hblanco2009(a)gmail.com>: > Hi Idwer, do you finally have any idea if the problem could be solved? > Henry Pleasse read, and reply to, the mailinglist for questions, don't reply to me or others without adding flashrom(a)flashrom.org to To: or Cc:. Thanks :) http://www.coreboot.org/pipermail/flashrom/2013-February/thread.html#10519 >>> > _______________________________________________ >>> > flashrom mailing list >>> > flashrom(a)flashrom.org >>> > http://www.flashrom.org/mailman/listinfo/flashrom >> >> >

1 0