February 2013 - flashrom - mail.coreboot.org

[PATCH] Add W25Q....W series.
by Stefan Tauner Feb. 22, 2013

Feb. 22, 2013

- Use ".V" (and "_V" in macros) for 3.3V Winbond 25Q chips. Rename the existing chips and add a .voltage entry where it was missing. - Use ".W" (and "_W" in macros) for 1.8V Winbond 25Q chips. - Add a feature flag for QPI-enabled chips: FEATURE_QPI. - Add W25Q20.W, W25Q40.W, W25Q80.W, W25Q16.W, W25Q32.W, W25Q64.W. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- flash.h | 1 + flashchips.c | 274 ++++++++++++++++++++++++++++++++++++++++++++++++++++++---- flashchips.h | 20 +++-- print.c | 26 +++--- 4 files changed, 287 insertions(+), 34 deletions(-) diff --git a/flash.h b/flash.h index a479286..b035330 100644 --- a/flash.h +++ b/flash.h @@ -99,6 +99,7 @@ enum write_granularity { #define FEATURE_WRSR_EWSR (1 << 6) #define FEATURE_WRSR_WREN (1 << 7) #define FEATURE_OTP (1 << 8) +#define FEATURE_QPI (1 << 9) #define FEATURE_WRSR_EITHER (FEATURE_WRSR_EWSR | FEATURE_WRSR_WREN) struct flashctx; diff --git a/flashchips.c b/flashchips.c index d4ab1be..0e0a1ff 100644 --- a/flashchips.c +++ b/flashchips.c @@ -9405,13 +9405,14 @@ const struct flashchip flashchips[] = { { .vendor = "Winbond", - .name = "W25Q80", + .name = "W25Q80.V", .bustype = BUS_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = WINBOND_NEX_W25Q80, + .model_id = WINBOND_NEX_W25Q80_V, .total_size = 1024, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* supports SFDP */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, @@ -9444,13 +9445,14 @@ const struct flashchip flashchips[] = { { .vendor = "Winbond", - .name = "W25Q16", + .name = "W25Q16.V", .bustype = BUS_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = WINBOND_NEX_W25Q16, + .model_id = WINBOND_NEX_W25Q16_V, .total_size = 2048, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* supports SFDP */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, @@ -9483,13 +9485,14 @@ const struct flashchip flashchips[] = { { .vendor = "Winbond", - .name = "W25Q32", + .name = "W25Q32.V", .bustype = BUS_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = WINBOND_NEX_W25Q32, + .model_id = WINBOND_NEX_W25Q32_V, .total_size = 4096, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* supports SFDP */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, @@ -9522,13 +9525,14 @@ const struct flashchip flashchips[] = { { .vendor = "Winbond", - .name = "W25Q64", + .name = "W25Q64.V", .bustype = BUS_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = WINBOND_NEX_W25Q64, + .model_id = WINBOND_NEX_W25Q64_V, .total_size = 8192, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* supports SFDP */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, @@ -9556,17 +9560,19 @@ const struct flashchip flashchips[] = { .unlock = spi_disable_blockprotect, .write = spi_chip_write_256, .read = spi_chip_read, + .voltage = {2700, 3600}, }, { .vendor = "Winbond", - .name = "W25Q128", + .name = "W25Q128.V", .bustype = BUS_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = WINBOND_NEX_W25Q128, + .model_id = WINBOND_NEX_W25Q128_V, .total_size = 16384, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* supports SFDP */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_OK_PROBE, .probe = probe_spi_rdid, @@ -9594,6 +9600,244 @@ const struct flashchip flashchips[] = { .unlock = spi_disable_blockprotect, .write = spi_chip_write_256, .read = spi_chip_read, + .voltage = {2700, 3600}, + }, + + { + .vendor = "Winbond", + .name = "W25Q20.W", + .bustype = BUS_SPI, + .manufacture_id = WINBOND_NEX_ID, + .model_id = WINBOND_NEX_W25Q20_W, + .total_size = 256, + .page_size = 256, + /* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 64} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 8} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 4} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {256 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_plain, /* TODO: improve */ + .unlock = spi_disable_blockprotect, + .write = spi_chip_write_256, + .read = spi_chip_read, + .voltage = {1700, 1950}, /* Fast read (0x0B) and multi I/O supported */ + }, + + { + .vendor = "Winbond", + .name = "W25Q40.W", + .bustype = BUS_SPI, + .manufacture_id = WINBOND_NEX_ID, + .model_id = WINBOND_NEX_W25Q40_W, + .total_size = 512, + .page_size = 256, + /* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 128} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 16} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 8} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {512 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_plain, /* TODO: improve */ + .unlock = spi_disable_blockprotect, + .write = spi_chip_write_256, + .read = spi_chip_read, + .voltage = {1700, 1950}, /* Fast read (0x0B) and multi I/O supported */ + }, + + { + .vendor = "Winbond", + .name = "W25Q80.W", + .bustype = BUS_SPI, + .manufacture_id = WINBOND_NEX_ID, + .model_id = WINBOND_NEX_W25Q80_W, + .total_size = 1024, + .page_size = 256, + /* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 256} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 32} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 16} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {1 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {1 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_plain, /* TODO: improve */ + .unlock = spi_disable_blockprotect, + .write = spi_chip_write_256, + .read = spi_chip_read, + .voltage = {1700, 1950}, /* Fast read (0x0B) and multi I/O supported */ + }, + + { + .vendor = "Winbond", + .name = "W25Q16.W", + .bustype = BUS_SPI, + .manufacture_id = WINBOND_NEX_ID, + .model_id = WINBOND_NEX_W25Q16_W, + .total_size = 2048, + .page_size = 256, + /* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ + /* QPI enable 0x38, disable 0xFF */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 512} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 64} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 32} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {2 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_plain, /* TODO: improve */ + .unlock = spi_disable_blockprotect, + .write = spi_chip_write_256, + .read = spi_chip_read, + .voltage = {1700, 1950}, /* Fast read (0x0B) and multi I/O supported */ + }, + + { + .vendor = "Winbond", + .name = "W25Q32.W", + .bustype = BUS_SPI, + .manufacture_id = WINBOND_NEX_ID, + .model_id = WINBOND_NEX_W25Q32_W, + .total_size = 4096, + .page_size = 256, + /* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ + /* QPI enable 0x38, disable 0xFF */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_OK_PREW, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 1024} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 128} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 64} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {4 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {4 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_plain, /* TODO: improve */ + .unlock = spi_disable_blockprotect, + .write = spi_chip_write_256, + .read = spi_chip_read, + .voltage = {1700, 1950}, /* Fast read (0x0B) and multi I/O supported */ + }, + + { + .vendor = "Winbond", + .name = "W25Q64.W", + .bustype = BUS_SPI, + .manufacture_id = WINBOND_NEX_ID, + .model_id = WINBOND_NEX_W25Q64_W, + .total_size = 8192, + .page_size = 256, + /* OTP: 256B total; read 0x48; write 0x42, erase 0x44, read ID 0x4B */ + /* QPI enable 0x38, disable 0xFF */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP | FEATURE_QPI, + .tested = TEST_OK_PREW, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 2048} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 256} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 128} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {8 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {8 * 1024 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_plain, /* TODO: improve */ + .unlock = spi_disable_blockprotect, + .write = spi_chip_write_256, + .read = spi_chip_read, + .voltage = {1700, 1950}, /* Fast read (0x0B) and multi I/O supported */ }, { diff --git a/flashchips.h b/flashchips.h index 1a0696f..d705c32 100644 --- a/flashchips.h +++ b/flashchips.h @@ -649,12 +649,20 @@ #define WINBOND_NEX_W25X16 0x3015 #define WINBOND_NEX_W25X32 0x3016 #define WINBOND_NEX_W25X64 0x3017 -#define WINBOND_NEX_W25Q40 0x4013 -#define WINBOND_NEX_W25Q80 0x4014 -#define WINBOND_NEX_W25Q16 0x4015 -#define WINBOND_NEX_W25Q32 0x4016 -#define WINBOND_NEX_W25Q64 0x4017 -#define WINBOND_NEX_W25Q128 0x4018 +#define WINBOND_NEX_W25Q40_V 0x4013 /* W25Q40BV; W25Q40BL (2.3-3.6V) */ +#define WINBOND_NEX_W25Q80_V 0x4014 /* W25Q80BV */ +#define WINBOND_NEX_W25Q16_V 0x4015 /* W25Q16CV; W25Q16DV */ +#define WINBOND_NEX_W25Q32_V 0x4016 /* W25Q32BV; W25Q32FV in SPI mode (default) */ +#define WINBOND_NEX_W25Q64_V 0x4017 /* W25Q64BV, W25Q64CV; W25Q64FV in SPI mode (default) */ +#define WINBOND_NEX_W25Q128_V 0x4018 /* W25Q128BV; W25Q128FV in SPI mode (default) */ +#define WINBOND_NEX_W25Q256_V 0x4019 /* W25Q256FV */ +#define WINBOND_NEX_W25Q20_W 0x5012 /* W25Q20BW */ +#define WINBOND_NEX_W25Q40_W 0x5013 /* W25Q40BW */ +#define WINBOND_NEX_W25Q80_W 0x5014 /* W25Q80BW */ +#define WINBOND_NEX_W25Q16_W 0x6015 /* W25Q16DW */ +#define WINBOND_NEX_W25Q32_W 0x6016 /* W25Q32DW; W25Q32FV in QPI mode */ +#define WINBOND_NEX_W25Q64_W 0x6017 /* W25Q64DW; W25Q64FV in QPI mode */ +#define WINBOND_NEX_W25Q128_W 0x6018 /* (No W version known) W25Q128FV in QPI mode */ #define WINBOND_ID 0xDA /* Winbond */ #define WINBOND_W19B160BB 0x49 diff --git a/print.c b/print.c index ecde90f..7d2e5a0 100644 --- a/print.c +++ b/print.c @@ -544,7 +544,7 @@ const struct board_info boards_known[] = { B("ASRock", "G31M-S rev 2.0", OK, "http://www.asrock.com/mb/overview.asp?model=G31M-S", NULL), B("ASRock", "ConRoeXFire-eSATA2", OK, "http://www.asrock.com/mb/overview.asp?model=conroexfire-esata2", NULL), B("ASRock", "H61M-ITX", BAD, "http://www.asrock.com/mb/overview.asp?Model=H61M-ITX", "Probing works (Macronix MX25L3205, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), - B("ASRock", "H67M", BAD, "http://www.asrock.com/mb/overview.asp?Model=H67M", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("ASRock", "H67M", BAD, "http://www.asrock.com/mb/overview.asp?Model=H67M", "Probing works (Winbond W25Q64.V, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASRock", "K7S41", OK, "http://www.asrock.com/mb/overview.asp?Model=K7S41", NULL), B("ASRock", "K7S41GX", OK, "http://www.asrock.com/mb/overview.asp?Model=K7S41GX", NULL), B("ASRock", "K7VT4A+", BAD, "http://www.asrock.com/mb/overview.asp?Model=K7VT4A%2b", "No chip found, probably due to flash translation. http://www.flashrom.org/pipermail/flashrom/2009-August/000393.html"), @@ -683,16 +683,16 @@ const struct board_info boards_known[] = { B("ASUS", "P6T Deluxe V2", OK, "http://www.asus.com/Motherboards/Intel_Socket_1366/P6T_Deluxe_V2/", NULL), B("ASUS", "P7H57D-V EVO", OK, "http://www.asus.com/Motherboards/Intel_Socket_1156/P7H57DV_EVO/", NULL), B("ASUS", "P7H55-M LX", BAD, NULL, "flashrom works correctly, but GbE LAN is nonworking (probably due to a missing/bogus MAC address; see http://www.flashrom.org/pipermail/flashrom/2011-July/007432.html and http://ubuntuforums.org/showthread.php?t=1534389 for a possible workaround)"), - B("ASUS", "P8B-E/4L", BAD, NULL, "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), - B("ASUS", "P8B WS", BAD, NULL, "Probing works (Winbond W25Q32, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), - B("ASUS", "P8H61 PRO", BAD, NULL, "Probing works (Winbond W25Q32, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), - B("ASUS", "P8H61-M LE/USB3", BAD, NULL, "Probing works (Winbond W25Q32, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("ASUS", "P8B-E/4L", BAD, NULL, "Probing works (Winbond W25Q64.V, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("ASUS", "P8B WS", BAD, NULL, "Probing works (Winbond W25Q32.V, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("ASUS", "P8H61 PRO", BAD, NULL, "Probing works (Winbond W25Q32.V, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("ASUS", "P8H61-M LE/USB3", BAD, NULL, "Probing works (Winbond W25Q32.V, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASUS", "P8H67-M PRO", BAD, NULL, "Probing works (Macronix MX25L3205, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASUS", "P8P67 (rev. 3.1)", BAD, NULL, "Probing works (Macronix MX25L3205, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), - B("ASUS", "P8P67 LE", BAD, NULL, "Probing works (Winbond W25Q32, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("ASUS", "P8P67 LE", BAD, NULL, "Probing works (Winbond W25Q32.V, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASUS", "P8P67 PRO (rev. 3.0)", OK, "http://www.asus.com/Motherboards/Intel_Socket_1155/P8P67_PRO/", NULL), B("ASUS", "P8Z68-V", OK, "http://www.asus.com/Motherboards/Intel_Socket_1155/P8Z68V/", "Warning: MAC address of LOM is stored at 0x1000 - 0x1005 of the image."), - B("ASUS", "P8Z68-V PRO", BAD, NULL, "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("ASUS", "P8Z68-V PRO", BAD, NULL, "Probing works (Winbond W25Q64.V, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASUS", "P8Z68-V PRO/GEN3", OK, "http://www.asus.com/Motherboards/Intel_Socket_1155/P8Z68V_PROGEN3/", "Warning: MAC address of LOM is stored at 0x1000 - 0x1005 of the image."), B("ASUS", "SABERTOOTH 990FX", OK, "http://www.asus.com/Motherboards/AMD_AM3Plus/SABERTOOTH_990FX/", NULL), B("ASUS", "SABERTOOTH 990FX R2.0", OK, "http://www.asus.com/Motherboards/AMD_AM3Plus/SABERTOOTH_990FX_R20/", NULL), @@ -895,8 +895,8 @@ const struct board_info boards_known[] = { B("MSI", "MS-7596 (785GM-E51)", OK, "http://www.msi.com/product/mb/785GM-E51.html", NULL), B("MSI", "MS-7597 (GF615M-P33)", BAD, NULL, "Missing board enable/SIO support (Fintek F71889), see http://www.flashrom.org/pipermail/flashrom/2012-March/008956.html"), B("MSI", "MS-7599 (870-C45)", OK, "http://www.msi.com/product/mb/870-C45.html", NULL), - B("MSI", "MS-7613 (Iona-GL8E)", BAD, "http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02014355&lc=en&cc=dk&d…", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), - B("MSI", "MS-7635 (H55M-ED55)", BAD, "http://www.msi.com/product/mb/H55M-ED55.html", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("MSI", "MS-7613 (Iona-GL8E)", BAD, "http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02014355&lc=en&cc=dk&d…", "Probing works (Winbond W25Q64.V, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("MSI", "MS-7635 (H55M-ED55)", BAD, "http://www.msi.com/product/mb/H55M-ED55.html", "Probing works (Winbond W25Q64.V, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("MSI", "MS-7640 (890FXA-GD70)",OK, "http://www.msi.com/product/mb/890FXA-GD70.html", NULL), B("MSI", "MS-7642 (890GXM-G65)", OK, "http://www.msi.com/product/mb/890GXM-G65.html", NULL), B("MSI", "MS-7676 (H67MA-ED55(B3))", OK, "http://www.msi.com/product/mb/H67MA-ED55--B3-.html", "Seems to work fine basically, but user reported (hopefully unrelated) buggy behavior of the board after a firmware upgrade. See http://www.flashrom.org/pipermail/flashrom/2012-January/008547.html"), @@ -956,8 +956,8 @@ const struct board_info boards_known[] = { B("Supermicro", "X9DRT-HF+", BAD, NULL, "Probing works (Numonyx N25Q128 (supported by SFDP only atm), 16384 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked; SMM protection enabled."), B("Supermicro", "X9DRW", BAD, NULL, "Probing works (Numonyx N25Q128 (supported by SFDP only atm), 16384 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("Supermicro", "X9QRi-F+", BAD, "http://www.supermicro.com/products/motherboard/Xeon/C600/X9QRi-F_.cfm", "Probing works (Macronix MX25L12805, 16384 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked; SMM protection enabled."), - B("Supermicro", "X9SCA-F", BAD, "http://www.supermicro.com/products/motherboard/Xeon/C202_C204/X9SCA-F.cfm", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), - B("Supermicro", "X9SCL", BAD, "http://www.supermicro.com/products/motherboard/Xeon/C202_C204/X9SCL.cfm", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("Supermicro", "X9SCA-F", BAD, "http://www.supermicro.com/products/motherboard/Xeon/C202_C204/X9SCA-F.cfm", "Probing works (Winbond W25Q64.V, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("Supermicro", "X9SCL", BAD, "http://www.supermicro.com/products/motherboard/Xeon/C202_C204/X9SCL.cfm", "Probing works (Winbond W25Q64.V, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("T-Online", "S-100", OK, "http://wiki.freifunk-hannover.de/T-Online_S_100", NULL), B("Tekram", "P6Pro-A5", OK, "http://www.motherboard.cz/mb/tekram/P6Pro-A5.htm", NULL), B("Termtek", "TK-3370 (Rev:2.5B)", OK, NULL, NULL), @@ -1010,8 +1010,8 @@ const struct board_info boards_known[] = { B("VIA", "VB700X", OK, "http://www.via.com.tw/en/products/mainboards/motherboards.jsp?motherboard_i…", NULL), B("ZOTAC", "Fusion-ITX WiFi (FUSION350-A-E)", OK, NULL, NULL), B("ZOTAC", "GeForce 8200", OK, NULL, NULL), - B("ZOTAC", "H61-ITX WiFi (H61ITX-A-E)", BAD, NULL, "Probing works (Winbond W25Q32, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), - B("ZOTAC", "H67-ITX WiFi (H67ITX-C-E)", BAD, NULL, "Probing works (Winbond W25Q32, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("ZOTAC", "H61-ITX WiFi (H61ITX-A-E)", BAD, NULL, "Probing works (Winbond W25Q32.V, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), + B("ZOTAC", "H67-ITX WiFi (H67ITX-C-E)", BAD, NULL, "Probing works (Winbond W25Q32.V, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ZOTAC", "nForce 630i Supreme (N73U-Supreme)", OK, NULL, NULL), B("ZOTAC", "ZBOX AD02 (PLUS)", OK, NULL, NULL), B("ZOTAC", "ZBOX HD-ID11", OK, NULL, NULL), -- Kind regards, Stefan Tauner

1 0

[commit] r1650 - trunk
by repository service Feb. 22, 2013

Feb. 22, 2013

Author: stefanct Date: Fri Feb 22 16:58:45 2013 New Revision: 1650 URL: http://flashrom.org/trac/flashrom/changeset/1650 Log: Add a bunch of new/tested stuff and various small changes 17. Tested Mainboards: OK: - Acer V75-M (used in IBM Aptiva 2170-G) http://www.flashrom.org/pipermail/flashrom/2012-December/010300.html - Acorp 6M810C http://www.flashrom.org/pipermail/flashrom/2013-January/010433.html - ASRock G31M-S rev 2.0 http://www.flashrom.org/pipermail/flashrom/2013-February/010538.html - ASUS F1A75-V PRO http://paste.flashrom.org/view.php?id=1528 - ASUS M5A97 (rev. 1.0) http://www.flashrom.org/pipermail/flashrom/2013-February/010483.html - ASUS P5KPL-AM IN/GB http://www.flashrom.org/pipermail/flashrom/2013-January/010455.html - GABYTE GA-H77M-D3H http://www.flashrom.org/pipermail/flashrom/2013-February/010538.html NOT OK: - GIGABYTE GA-Z77MX-D3H http://paste.flashrom.org/view.php?id=1529 http://paste.flashrom.org/view.php?id=1530 Tested flash chips: - Winbond W25X10 to PREW (+PREW) Reported on IRC(?) - Eon EN25Q32(A/B) to PREW (+REW) http://www.flashrom.org/pipermail/flashrom/2013-February/010533.html - Eon EN25Q64 to PREW (+PREW) http://www.flashrom.org/pipermail/flashrom/2013-January/010466.html Miscellaneous: - Fix superflouos line breaks in wiki mainboard and laptop output. - Use the .nh (no hyphenation) command in the manpage to enforce single-line URLs where useful. - Reference the manpage (besides the Laptops wiki page) in the laptop warning. - Minor output and whitespace fixes. - Add Fidelix IDs. - Add ISSE clones of PMC chips. - Fix typo: EMST -> ESMT. - Add ID of ESMT F25D08QA. - Refine GigaDevice GD25Q series (missing voltages and comments). - Use underscore instead of lower-case x as wildcard in Sharp chip names. Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Modified: trunk/flashchips.c trunk/flashchips.h trunk/flashrom.8 trunk/internal.c trunk/it87spi.c trunk/print.c trunk/print_wiki.c Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Wed Feb 20 19:03:36 2013 (r1649) +++ trunk/flashchips.c Fri Feb 22 16:58:45 2013 (r1650) @@ -2713,11 +2713,11 @@ }, { - .vendor = "EMST", + .vendor = "ESMT", .name = "F49B002UA", .bustype = BUS_PARALLEL, - .manufacture_id = EMST_ID, - .model_id = EMST_F49B002UA, + .manufacture_id = ESMT_ID, + .model_id = ESMT_F49B002UA, .total_size = 256, .page_size = 4096, .feature_bits = FEATURE_EITHER_RESET, @@ -2745,11 +2745,11 @@ }, { - .vendor = "EMST", + .vendor = "ESMT", .name = "F25L008A", .bustype = BUS_SPI, - .manufacture_id = EMST_ID, - .model_id = EMST_F25L008A, + .manufacture_id = ESMT_ID, + .model_id = ESMT_F25L008A, .total_size = 1024, .page_size = 256, .feature_bits = FEATURE_WRSR_EITHER, @@ -3748,7 +3748,7 @@ .page_size = 256, /* OTP: 512B total; enter 0x3A */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, - .tested = TEST_OK_PROBE, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -3784,7 +3784,7 @@ .page_size = 256, /* OTP: 512B total; enter 0x3A */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, - .tested = TEST_UNTESTED, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = @@ -4248,13 +4248,13 @@ { .vendor = "GigaDevice", - .name = "GD25Q80", + .name = "GD25Q80(B)", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25Q80, .total_size = 1024, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (B version only) */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, @@ -4293,7 +4293,7 @@ .model_id = GIGADEVICE_GD25Q16, .total_size = 2048, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 (B version only) */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_UNTESTED, .probe = probe_spi_rdid, @@ -4326,13 +4326,13 @@ { .vendor = "GigaDevice", - .name = "GD25Q32", + .name = "GD25Q32(B)", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25Q32, .total_size = 4096, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_UNTESTED, .probe = probe_spi_rdid, @@ -4365,13 +4365,13 @@ { .vendor = "GigaDevice", - .name = "GD25Q64", + .name = "GD25Q64(B)", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25Q64, .total_size = 8192, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, @@ -4399,17 +4399,18 @@ .unlock = spi_disable_blockprotect, .write = spi_chip_write_256, .read = spi_chip_read, + .voltage = {2700, 3600}, }, { .vendor = "GigaDevice", - .name = "GD25Q128", + .name = "GD25Q128B", .bustype = BUS_SPI, .manufacture_id = GIGADEVICE_ID, .model_id = GIGADEVICE_GD25Q128, .total_size = 16384, .page_size = 256, - /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42 */ + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */ .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_UNTESTED, .probe = probe_spi_rdid, @@ -4437,6 +4438,7 @@ .unlock = spi_disable_blockprotect, .write = spi_chip_write_256, .read = spi_chip_read, + .voltage = {2700, 3600}, }, { @@ -4447,7 +4449,8 @@ .model_id = GIGADEVICE_GD25LQ32, .total_size = 4096, .page_size = 256, - .feature_bits = FEATURE_WRSR_WREN, + /* OTP: 1024B total, 256B reserved; read 0x48; write 0x42, erase 0x44 */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_OTP, .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, @@ -6687,7 +6690,7 @@ .name = "LH28F008BJT-BTLZ1", .bustype = BUS_PARALLEL, .manufacture_id = SHARP_ID, - .model_id = SHARP_LH28F008BJxxPB, + .model_id = SHARP_LH28F008BJ__PB, .total_size = 1024, .page_size = 64 * 1024, .tested = TEST_OK_PREW, Modified: trunk/flashchips.h ============================================================================== --- trunk/flashchips.h Wed Feb 20 19:03:36 2013 (r1649) +++ trunk/flashchips.h Fri Feb 22 16:58:45 2013 (r1650) @@ -201,9 +201,10 @@ #define CATALYST_ID 0x31 /* Catalyst */ #define CATALYST_CAT28F512 0xB8 -#define EMST_ID 0x8C /* EMST / EFST Elite Flash Storage */ -#define EMST_F25L008A 0x2014 -#define EMST_F49B002UA 0x00 +#define ESMT_ID 0x8C /* Elite Semiconductor Memory Technology (ESMT) / EFST Elite Flash Storage */ +#define ESMT_F25L008A 0x2014 +#define ESMT_F25D08QA 0x2534 +#define ESMT_F49B002UA 0x00 /* * EN25 chips are SPI, first byte of device ID is memory type, @@ -265,6 +266,15 @@ #define EON_EN29F002T 0x7F92 /* Same as EN29F002A */ #define EON_EN29F002B 0x7F97 /* Same as EN29F002AN */ +#define FIDELIX_ID 0xF8 /* Fidelix */ +#define FIDELIX_FM25M16 0x4215 +#define FIDELIX_FM25M32 0x4216 +#define FIDELIX_FM25M64 0x4217 +#define FIDELIX_FM25Q08 0x3214 +#define FIDELIX_FM25Q16 0x3215 /* Same as FM25S16 (which is apparently single I/O only) */ +#define FIDELIX_FM25Q32 0x3216 +#define FIDELIX_FM25Q64 0x3217 + #define FUJITSU_ID 0x04 /* Fujitsu */ #define FUJITSU_MBM29DL400BC 0x0F #define FUJITSU_MBM29DL400TC 0x0C @@ -299,11 +309,11 @@ #define GIGADEVICE_ID 0xC8 /* GigaDevice */ #define GIGADEVICE_GD25Q20 0x4012 #define GIGADEVICE_GD25Q40 0x4013 -#define GIGADEVICE_GD25Q80 0x4014 -#define GIGADEVICE_GD25Q16 0x4015 -#define GIGADEVICE_GD25Q32 0x4016 -#define GIGADEVICE_GD25Q64 0x4017 -#define GIGADEVICE_GD25Q128 0x4018 +#define GIGADEVICE_GD25Q80 0x4014 /* Same as GD25Q80B (which has OTP) */ +#define GIGADEVICE_GD25Q16 0x4015 /* Same as GD25Q16B (which has OTP) */ +#define GIGADEVICE_GD25Q32 0x4016 /* Same as GD25Q32B */ +#define GIGADEVICE_GD25Q64 0x4017 /* Same as GD25Q64B */ +#define GIGADEVICE_GD25Q128 0x4018 /* GD25Q128B only? */ #define GIGADEVICE_GD25LQ32 0x6016 #define HYUNDAI_ID 0xAD /* Hyundai */ @@ -451,10 +461,10 @@ #define PMC_PM25LV016B 0x14 #define PMC_PM29F002T 0x1D #define PMC_PM29F002B 0x2D -#define PMC_PM39LV512 0x1B -#define PMC_PM39F010 0x1C /* Same as Pm39LV010 */ +#define PMC_PM39LV512 0x1B /* Same as IS39LV512 */ +#define PMC_PM39F010 0x1C /* Same as Pm39LV010, IS39LV010 */ #define PMC_PM39LV020 0x3D -#define PMC_PM39LV040 0x3E +#define PMC_PM39LV040 0x3E /* Same as IS39LV040 */ #define PMC_PM39F020 0x4D #define PMC_PM39F040 0x4E #define PMC_PM49FL002 0x6D @@ -469,11 +479,11 @@ #define SANYO_LE25FW203A 0x1600 #define SHARP_ID 0xB0 /* Sharp */ -#define SHARP_LH28F008BJxxPT 0xEC -#define SHARP_LH28F008BJxxPB 0xED -#define SHARP_LH28F800BVxxBTL 0x4B -#define SHARP_LH28F800BVxxBV 0x4D -#define SHARP_LH28F800BVxxTV 0x4C +#define SHARP_LH28F008BJ__PT 0xEC +#define SHARP_LH28F008BJ__PB 0xED +#define SHARP_LH28F800BV__BTL 0x4B +#define SHARP_LH28F800BV__BV 0x4D +#define SHARP_LH28F800BV__TV 0x4C #define SHARP_LHF00L02 0xC9 /* Same as LHF00L06/LHF00L07 */ #define SHARP_LHF00L04 0xCF /* Same as LHF00L03/LHF00L05 */ Modified: trunk/flashrom.8 ============================================================================== --- trunk/flashrom.8 Wed Feb 20 19:03:36 2013 (r1649) +++ trunk/flashrom.8 Fri Feb 22 16:58:45 2013 (r1650) @@ -161,6 +161,7 @@ .BR \-\-list\-supported , but outputs the supported hardware in MediaWiki syntax, so that it can be easily pasted into the wiki page at +.nh .BR http://www.flashrom.org/ . Please note that MediaWiki output is not compiled in by default. .TP @@ -390,6 +391,7 @@ .B BUGS section). The embedded controller (EC) in these machines often interacts badly with flashing. +.nh .B http://www.flashrom.org/Laptops has more information. For example the EC firmware sometimes resides on the same flash chip as the host firmware. While flashrom tries to change the contents of @@ -715,8 +717,10 @@ (DLC 5). .sp More information about the RayeR hardware is available at +.nh .BR "http://rayer.ic.cz/elektro/spipgm.htm " . The schematic of the Xilinx DLC 5 was published at +.nh .BR "http://www.xilinx.com/itp/xilinx4/data/docs/pac/appendixb.html " . .SS .BR "pony_spi " programmer @@ -730,6 +734,7 @@ parameter accepts the values "si_prog" (default) or "serbang". .sp Information about the SI-Prog adapter can be found at +.nh .BR "http://www.lancos.com/siprogsch.html " . .sp An example call to flashrom is @@ -765,6 +770,7 @@ section above. .sp More information about the hardware is available at +.nh .BR http://wiki.opengraphics.org . .SS .BR "linux_spi " programmer @@ -869,6 +875,7 @@ too. Please provide a way to contact you later (e.g.\& a mail address) and be patient if there is no immediate reaction. Also, we provide a pastebin service at +.nh .B http://paste.flashrom.org that is very useful when you want to share logs etc.\& without spamming the channel. @@ -884,8 +891,8 @@ .B internal programmer subsection of the .B PROGRAMMER SPECIFIC INFO -section. -.B " http://www.flashrom.org/Laptops" +section and the information in our wiki at +.BR "http://www.flashrom.org/Laptops " . .SS One-time programmable (OTP) memory and unique IDs .sp Modified: trunk/internal.c ============================================================================== --- trunk/internal.c Wed Feb 20 19:03:36 2013 (r1649) +++ trunk/internal.c Fri Feb 22 16:58:45 2013 (r1650) @@ -299,7 +299,7 @@ msg_perr("Laptops, notebooks and netbooks are difficult to support and we\n" "recommend to use the vendor flashing utility. The embedded controller\n" "(EC) in these machines often interacts badly with flashing.\n" - "See http://www.flashrom.org/Laptops for details.\n\n" + "See the manpage and http://www.flashrom.org/Laptops for details.\n\n" "If flash is shared with the EC, erase is guaranteed to brick your laptop\n" "and write may brick your laptop.\n" "Read and probe may irritate your EC and cause fan failure, backlight\n" Modified: trunk/it87spi.c ============================================================================== --- trunk/it87spi.c Wed Feb 20 19:03:36 2013 (r1649) +++ trunk/it87spi.c Fri Feb 22 16:58:45 2013 (r1650) @@ -87,15 +87,12 @@ case 0x86: case 0x87: /* FIXME: Print revision for all models? */ - msg_pdbg("Found ITE Super I/O, ID 0x%04hx on port " - "0x%x\n", s.model, s.port); + msg_pdbg("Found ITE Super I/O, ID 0x%04hx on port 0x%x\n", s.model, s.port); register_superio(s); break; case 0x85: - msg_pdbg("Found ITE EC, ID 0x%04hx," - "Rev 0x%02x on port 0x%x.\n", - s.model, sio_read(s.port, CHIP_VER_REG), - s.port); + msg_pdbg("Found ITE EC, ID 0x%04hx, Rev 0x%02x on port 0x%x.\n", + s.model, sio_read(s.port, CHIP_VER_REG), s.port); register_superio(s); break; } Modified: trunk/print.c ============================================================================== --- trunk/print.c Wed Feb 20 19:03:36 2013 (r1649) +++ trunk/print.c Fri Feb 22 16:58:45 2013 (r1650) @@ -519,6 +519,7 @@ B("abit", "VT6X4", OK, NULL, NULL), B("Acer", "V75-M", OK, NULL, "This is an OEM board used by IBM in e.g. Aptiva 2170-G"), B("Acorp", "6A815EPD", OK, "http://web.archive.org/web/20021206163652/www.acorp.com.tw/English/default.…", NULL), + B("Acorp", "6M810C", OK, NULL, NULL), B("Advantech", "PCM-5820", OK, "http://www.emacinc.com/sbc_pc_compatible/pcm_5820.htm", NULL), B("agami", "Aruma", OK, "http://web.archive.org/web/20080212111524/http://www.agami.com/site/ais-600…", NULL), B("Albatron", "PM266A Pro", OK, "http://www.albatron.com.tw/English/Product/MB/pro_detail.asp?rlink=Overview…", NULL), /* FIXME */ @@ -540,6 +541,7 @@ B("ASRock", "ALiveNF6G-DVI", OK, "http://www.asrock.com/mb/overview.asp?Model=ALiveNF6G-DVI", NULL), B("ASRock", "AM2NF6G-VSTA", OK, "http://www.asrock.com/mb/overview.asp?Model=AM2NF6G-VSTA", NULL), B("ASRock", "E350M1/USB3", OK, "http://www.asrock.com/mb/overview.asp?model=e350m1/usb3", NULL), + B("ASRock", "G31M-S rev 2.0", OK, "http://www.asrock.com/mb/overview.asp?model=G31M-S", NULL), B("ASRock", "ConRoeXFire-eSATA2", OK, "http://www.asrock.com/mb/overview.asp?model=conroexfire-esata2", NULL), B("ASRock", "H61M-ITX", BAD, "http://www.asrock.com/mb/overview.asp?Model=H61M-ITX", "Probing works (Macronix MX25L3205, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASRock", "H67M", BAD, "http://www.asrock.com/mb/overview.asp?Model=H67M", "Probing works (Winbond W25Q64, 8192 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), @@ -577,6 +579,7 @@ B("ASUS", "Crosshair IV Extreme", OK, "http://www.asus.com/Motherboards/AMD_AM3/Crosshair_IV_Extreme/", NULL), B("ASUS", "DSAN-DX", NT, "http://www.asus.com/Server_Workstation/Server_Motherboards/DSANDX/", NULL), B("ASUS", "E35M1-I DELUXE", OK, "http://www.asus.com/Motherboards/AMD_CPU_on_Board/E35M1I_DELUXE/", NULL), + B("ASUS", "F1A75-V PRO", OK, "http://www.asus.com/Motherboard/F1A75V_PRO/", NULL), B("ASUS", "K8N", OK, "http://www.asus.com/Motherboards/AMD_Socket_754/K8N/", NULL), B("ASUS", "K8V", OK, "http://www.asus.com/Motherboards/AMD_Socket_754/K8V/", NULL), B("ASUS", "K8V SE Deluxe", OK, "http://www.asus.com/Motherboards/AMD_Socket_754/K8V_SE_Deluxe/", NULL), @@ -611,6 +614,7 @@ B("ASUS", "M4N68T V2", OK, "http://www.asus.com/Motherboards/AMD_AM3/M4N68T_V2/", NULL), B("ASUS", "M4N78 PRO", OK, "http://www.asus.com/Motherboards/AMD_AM2Plus/M4N78_PRO/", NULL), B("ASUS", "M5A78L-M LX", OK, "http://www.asus.com/Motherboards/AMD_AM3Plus/M5A78LM_LX/", "The MAC address of the onboard LAN NIC is stored in flash, hence overwritten by flashrom; see http://www.flashrom.org/pipermail/flashrom/2012-May/009200.html"), + B("ASUS", "M5A97 (rev. 1.0)", OK, "http://www.asus.com/Motherboard/M5A97/", NULL), B("ASUS", "M5A99X EVO", OK, "http://www.asus.com/Motherboards/AMD_AM3Plus/M5A99X_EVO/", NULL), B("ASUS", "Maximus IV Extreme", BAD, "http://www.asus.com/Motherboards/Intel_Socket_1155/Maximus_IV_Extreme/", "Probing works (Macronix MX25L3205, 4096 kB, SPI), but parts of the flash are problematic: descriptor is r/o (conforming to ICH reqs), ME region is locked."), B("ASUS", "MEW-AM", BAD, NULL, "No public report found. Owned by Uwe Hermann <uwe(a)hermann-uwe.de>. May work now."), @@ -656,6 +660,7 @@ B("ASUS", "P5K-V", OK, "http://www.asus.com/Motherboards/Intel_Socket_775/P5KV/", NULL), B("ASUS", "P5K-VM", OK, "http://www.asus.com/Motherboards/Intel_Socket_775/P5KVM/", NULL), B("ASUS", "P5KC", OK, "http://www.asus.com/Motherboards/Intel_Socket_775/P5KC/", NULL), + B("ASUS", "P5KPL-AM IN/GB", OK, "http://support.asus.com/download.aspx?SLanguage=en&m=P5KPL-AM+IN%2fGB&os=29", NULL), B("ASUS", "P5KPL-CM", OK, "http://www.asus.com/Motherboards/Intel_Socket_775/P5KPLCM/", NULL), B("ASUS", "P5L-MX", OK, "http://www.asus.com/Motherboards/Intel_Socket_775/P5LMX/", NULL), B("ASUS", "P5L-VM 1394", OK, "http://www.asus.com/Motherboards/Intel_Socket_775/P5LVM_1394/", NULL), @@ -777,6 +782,7 @@ B("GIGABYTE", "GA-H61M-D2-B3", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3773", NULL), B("GIGABYTE", "GA-H61M-D2H-USB3", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4004", NULL), B("GIGABYTE", "GA-H77-D3H", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4141", "Does only work with -p internal:ich_spi_mode=hwseq due to an evil twin of MX25L6405 and ICH SPI lockdown."), + B("GIGABYTE", "GA-H77M-D3H", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=4388", NULL), B("GIGABYTE", "GA-EX58-UD4P", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=2986", NULL), B("GIGABYTE", "GA-K8N-SLI", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=1928", NULL), B("GIGABYTE", "GA-K8N51GMF", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=1950", NULL), @@ -804,6 +810,7 @@ B("GIGABYTE", "GA-X79-UD5", OK, NULL, NULL), B("GIGABYTE", "GA-Z68MX-UD2H-B (rev. 1.3)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3854", NULL), B("GIGABYTE", "GA-Z68XP-UD3 (rev. 1.0)", OK, "http://www.gigabyte.com/products/product-page.aspx?pid=3892", NULL), + B("GIGABYTE", "GA-Z77MX-D3H", BAD, "http://www.gigabyte.com/products/product-page.aspx?pid=4145", "Uses MX25L6436E and requires a small patch (but works flawlessly with that)."), B("HP", "8100 Elite CMT PC (304Bh)", BAD, NULL, "SPI lock down, PR, read-only descriptor, locked ME region."), B("HP", "e-Vectra P2706T", OK, "http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?lang=en&cc=us&pro…", NULL), B("HP", "ProLiant DL145 G3", OK, "http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c008…", NULL), Modified: trunk/print_wiki.c ============================================================================== --- trunk/print_wiki.c Wed Feb 20 19:03:36 2013 (r1649) +++ trunk/print_wiki.c Fri Feb 22 16:58:45 2013 (r1650) @@ -209,7 +209,7 @@ /* end inner table if it did not fill the last column fully */ if (((i % lines_per_col)) > 0) printf("\n|}\n\n"); - printf("\n\n|}\n"); + printf("|}\n"); if (num_notes > 0) printf("\n<small>\n%s</small>\n", notes);

1 0

Re: [flashrom] Added chipsets
by Stefan Tauner Feb. 22, 2013

Feb. 22, 2013

On Fri, 22 Feb 2013 08:58:54 +0400 Николай Николаев <evrinoma(a)gmail.com> wrote: >> these look like typos? > This is not typos. I'm verified again all documentation. > The chip S25FL128S has a Device Identification like a 2018 (table 11.2 page > 133) > The chip S25FL256S has a Device Identification like a 0219 (table 11.2 page > 133) > The chip S25FL256S has a Device Identification like a 0220 (table 11.4 page > 123) >> +#define SPANSION_S25FL128 0x2018 >> +#define SPANSION_S25FL256 0x0219 >> +#define SPANSION_S25FL512 0x0220 hm... still looks like a typo, but maybe not your typo (well, you added a typo now in the last line but that's not what I am talking about ;) It would not be the first time that a datasheet has wrong IDs. It just happens too easily. In general it would be best to verify that with actual hardware and/or to contact the manufacturer. I have no time to look into this now in detail. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Re: [flashrom] Added chipsets
by Stefan Tauner Feb. 22, 2013

Feb. 22, 2013

On Fri, 22 Feb 2013 08:07:33 +0300 Peter Lemenkov <lemenkov(a)gmail.com> wrote: > Hello! > > 2013/2/22 Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at>: > > > It would also make sense to split your huge patch into smaller pieces > > (e.g. one patch per manufacturer) so that we can review it easier. > > Maybe it's time to consider switching to Git entirely? Git is much > more better suited for this kind of task. You need to convince Carl-Daniel not me :) I have never checked out flashrom with subversion directly, only with git-svn and that works very nicely and there is no reason why submitting patches would be easier due to a switch to git alone (i.e. when we still demand patches to be sent to the mailing list instead of pull requests on github or something similar). As said, I use it all the time and there has been no problems with the patches generated by me or anybody else using git AFAIK. Also, Carl-Daniel repeatedly said there is no way he will switch to git and since there is no immediate need to do so this will not happen in the near future. If anybody has major problems with the git-svn/git send-email workflow he can also send me pull requests on github https://github.com/stefanct/flashrom But I don't make any promises that I will merge them in a timely manner *or at all* and this should be regarded as the last resort. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

[PATCH] dediprog: Use asynchronous bulk transfers for reading
by Nico Huber Feb. 22, 2013

Feb. 22, 2013

This utilizes libusb-1.0's interface for asynchronous transfers. A read is split into 512 byte chunks as required by the dediprog hardware. Up to eight chunks are scheduled for asynchronous transfer which results in a viable speed-up. First tests have shown a three times speed increase. Signed-off-by: Nico Huber <nico.huber(a)secunet.com> --- dediprog.c | 92 ++++++++++++++++++++++++++++++++++++++++++++++++++++++------ 1 file changed, 83 insertions(+), 9 deletions(-) diff --git a/dediprog.c b/dediprog.c index 93c4072..3cd7b01 100644 --- a/dediprog.c +++ b/dediprog.c @@ -31,6 +31,7 @@ #define FIRMWARE_VERSION(x,y,z) ((x << 16) | (y << 8) | z) #define DEFAULT_TIMEOUT 3000 +#define DEDIPROG_ASYNC_TRANSFERS 8 /* at most 8 asynchronous transfers */ static libusb_context *usb_ctx; static libusb_device_handle *dediprog_handle; static int dediprog_firmwareversion; @@ -235,6 +236,38 @@ static int dediprog_set_spi_speed(unsigned int spispeed_idx) return 0; } +struct dediprog_transfer_status { + int error; /* OK if 0, ERROR else */ + unsigned int queued_idx; + unsigned int finished_idx; +}; + +static void dediprog_bulk_read_cb(struct libusb_transfer *const transfer) +{ + struct dediprog_transfer_status *const status = (struct dediprog_transfer_status *)transfer->user_data; + if (transfer->status != LIBUSB_TRANSFER_COMPLETED) { + status->error = 1; + msg_perr("SPI bulk read failed!\n"); + } + ++status->finished_idx; +} + +static int dediprog_bulk_read_poll(const struct dediprog_transfer_status *const status, const int finish) +{ + if (status->finished_idx >= status->queued_idx) + return 0; + + do { + struct timeval timeout = { 10, 0 }; + const int ret = libusb_handle_events_timeout_completed(usb_ctx, &timeout, NULL); + if (ret < 0) { + msg_perr("Polling read events failed: %i %s!\n", ret, libusb_error_name(ret)); + return 1; + } + } while (finish && (status->finished_idx < status->queued_idx)); + return 0; +} + /* Bulk read interface, will read multiple 512 byte chunks aligned to 512 bytes. * @start start address * @len length @@ -243,7 +276,7 @@ static int dediprog_set_spi_speed(unsigned int spispeed_idx) static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len) { - int ret, transferred; + int ret, err = 1; unsigned int i; /* chunksize must be 512, other sizes will NOT work at all. */ const unsigned int chunksize = 0x200; @@ -253,6 +286,10 @@ static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, chunksize & 0xff, (chunksize >> 8) & 0xff }; + struct dediprog_transfer_status status = { 0, 0, 0 }; + struct libusb_transfer *transfers[DEDIPROG_ASYNC_TRANSFERS] = { NULL, }; + struct libusb_transfer *transfer; + if ((start % chunksize) || (len % chunksize)) { msg_perr("%s: Unaligned start=%i, len=%i! Please report a bug " "at flashrom(a)flashrom.org\n", __func__, start, len); @@ -273,17 +310,54 @@ static int dediprog_spi_bulk_read(struct flashctx *flash, uint8_t *buf, return 1; } - for (i = 0; i < count; i++) { - ret = libusb_bulk_transfer(dediprog_handle, 0x80 | dediprog_endpoint, - buf + i * chunksize, chunksize, &transferred, DEFAULT_TIMEOUT); - if ((ret < 0) || (transferred != chunksize)) { - msg_perr("SPI bulk read %i failed, expected %i, got %i %s!\n", - i, chunksize, ret, libusb_error_name(ret)); - return 1; + /* + * Ring buffer of bulk transfers. + * Poll until at least one transfer is ready, + * schedule next transfers until buffer is full. + */ + + /* Allocate bulk transfers. */ + for (i = 0; i < min(DEDIPROG_ASYNC_TRANSFERS, count); ++i) { + transfers[i] = libusb_alloc_transfer(0); + if (!transfers[i]) { + msg_perr("Allocating libusb transfer %i failed: %s!\n", i, libusb_error_name(ret)); + goto _err_free; } } - return 0; + /* Now transfer requested chunks using libusb's asynchronous interface. */ + while (!status.error && (status.queued_idx < count)) { + while ((status.queued_idx - status.finished_idx) < DEDIPROG_ASYNC_TRANSFERS) { + transfer = transfers[status.queued_idx % DEDIPROG_ASYNC_TRANSFERS]; + libusb_fill_bulk_transfer(transfer, dediprog_handle, 0x80 | dediprog_endpoint, + (unsigned char *)buf + status.queued_idx * chunksize, chunksize, + dediprog_bulk_read_cb, &status, DEFAULT_TIMEOUT); + transfer->flags |= LIBUSB_TRANSFER_SHORT_NOT_OK; + ret = libusb_submit_transfer(transfer); + if (ret < 0) { + msg_perr("Submitting SPI bulk read %i failed: %i %s!\n", + status.queued_idx, ret, libusb_error_name(ret)); + goto _err_free; + } + ++status.queued_idx; + } + if (dediprog_bulk_read_poll(&status, 0)) + goto _err_free; + } + /* Wait for transfers to finish. */ + if (dediprog_bulk_read_poll(&status, 1)) + goto _err_free; + /* Check if everything has been transmitted. */ + if ((status.finished_idx < count) || status.error) + goto _err_free; + + err = 0; + +_err_free: + dediprog_bulk_read_poll(&status, 1); + for (i = 0; i < DEDIPROG_ASYNC_TRANSFERS; ++i) + if (transfers[i]) libusb_free_transfer(transfers[i]); + return err; } static int dediprog_spi_read(struct flashctx *flash, uint8_t *buf, -- 1.7.9.5

1 0

Re: [flashrom] Added chipsets
by Stefan Tauner Feb. 22, 2013

Feb. 22, 2013

Hello Николай, that's quite some work you have done, thank you. There is one very important bit missing though: the signed-off-by line that certifies that you are legally allowed to release these changes under a free license. Please see http://flashrom.org/Development_Guidelines and http://www.coreboot.org/Development_Guidelines#Sign-off_Procedure for details. We can not commit your changes without this. It would also make sense to split your huge patch into smaller pieces (e.g. one patch per manufacturer) so that we can review it easier. I have not looked at the patch in detail, but some naming will have to change probably. > +#define SPANSION_S25FL128 0x2018 > +#define SPANSION_S25FL256 0x0219 > +#define SPANSION_S25FL512 0x0220 these look like typos? -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

3 3

EN25Q32(A/B) fully tested
by Lucian Langa Feb. 22, 2013

Feb. 22, 2013

Hi, I just tested EN25Q32 chip on a raspberry spi programmer. The memory chip comes from a TP-LINK router (mr3220v2) that contains this chips. I used flashrom+rpi(spi) to reflash router firmware, as I previously bricked the router beyond the recovery. I have desoldered the chip from the router and connected it directly to the raspberry headers. All in all it went fine I managed to reflash the chip and router works fine now. See attached logs from all operation I used (READ/ERASE/WRITE) Cheers, --lucian

2 1

Logs for ASRock G31M-S rev 2.0, Gigabyte GA-H77M-D3H rev. 1.1
by Александр Владимирович Feb. 22, 2013

Feb. 22, 2013

Logs for ASRock G31M-S rev 2.0, Gigabyte GA-H77M-D3H rev. 1.1

2 1

[commit] r1649 - trunk
by repository service Feb. 20, 2013

Feb. 20, 2013

Author: hailfinger Date: Wed Feb 20 19:03:36 2013 New Revision: 1649 URL: http://flashrom.org/trac/flashrom/changeset/1649 Log: Adds a programmer parameter 'spispeed' to the dediprog driver to control the transfer rate on the spi bus. The following rates are available (in Hz): 375k, 750k, 1.5M, 2.18M, 3M, 8M, 12M and 24M The original driver reinitializes the programmer after setting the speed, so the initialization calls have moved into a new function dediprog_setup() which is called twice. Signed-off-by: Nico Huber <nico.huber(a)secunet.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/dediprog.c trunk/flashrom.8 Modified: trunk/dediprog.c ============================================================================== --- trunk/dediprog.c Mon Feb 4 05:38:42 2013 (r1648) +++ trunk/dediprog.c Wed Feb 20 19:03:36 2013 (r1649) @@ -158,7 +158,23 @@ return 0; } -#if 0 +struct dediprog_spispeeds { + const char *const name; + const int speed; +}; + +static const struct dediprog_spispeeds spispeeds[] = { + { "24M", 0x0 }, + { "12M", 0x2 }, + { "8M", 0x1 }, + { "3M", 0x3 }, + { "2.18M", 0x4 }, + { "1.5M", 0x5 }, + { "750k", 0x6 }, + { "375k", 0x7 }, + { NULL, 0x0 }, +}; + /* After dediprog_set_spi_speed, the original app always calls * dediprog_set_spi_voltage(0) and then * dediprog_check_devicestring() four times in a row. @@ -166,56 +182,20 @@ * This looks suspiciously like the microprocessor in the SF100 has to be * restarted/reinitialized in case the speed changes. */ -static int dediprog_set_spi_speed(uint16_t speed) +static int dediprog_set_spi_speed(unsigned int spispeed_idx) { int ret; - unsigned int khz; - /* Case 1 and 2 are in weird order. Probably an organically "grown" - * interface. - * Base frequency is 24000 kHz, divisors are (in order) - * 1, 3, 2, 8, 11, 16, 32, 64. - */ - switch (speed) { - case 0x0: - khz = 24000; - break; - case 0x1: - khz = 8000; - break; - case 0x2: - khz = 12000; - break; - case 0x3: - khz = 3000; - break; - case 0x4: - khz = 2180; - break; - case 0x5: - khz = 1500; - break; - case 0x6: - khz = 750; - break; - case 0x7: - khz = 375; - break; - default: - msg_perr("Unknown frequency selector 0x%x! Aborting.\n", speed); - return 1; - } - msg_pdbg("Setting SPI speed to %u kHz\n", khz); + msg_pdbg("SPI speed is %sHz\n", spispeeds[spispeed_idx].name); - ret = usb_control_msg(dediprog_handle, 0x42, 0x61, speed, 0xff, NULL, - 0x0, DEFAULT_TIMEOUT); + ret = usb_control_msg(dediprog_handle, 0x42, 0x61, spispeeds[spispeed_idx].speed, 0xff, + NULL, 0x0, DEFAULT_TIMEOUT); if (ret != 0x0) { - msg_perr("Command Set SPI Speed 0x%x failed!\n", speed); + msg_perr("Command Set SPI Speed 0x%x failed!\n", spispeeds[spispeed_idx].speed); return 1; } return 0; } -#endif /* Bulk read interface, will read multiple 512 byte chunks aligned to 512 bytes. * @start start address @@ -742,6 +722,28 @@ return millivolt; } +static int dediprog_setup(void) +{ + /* URB 6. Command A. */ + if (dediprog_command_a()) { + return 1; + } + /* URB 7. Command A. */ + if (dediprog_command_a()) { + return 1; + } + /* URB 8. Command Prepare Receive Device String. */ + /* URB 9. Command Receive Device String. */ + if (dediprog_check_devicestring()) { + return 1; + } + /* URB 10. Command C. */ + if (dediprog_command_c()) { + return 1; + } + return 0; +} + static const struct spi_programmer spi_programmer_dediprog = { .type = SPI_CONTROLLER_DEDIPROG, .max_data_read = MAX_DATA_UNSPECIFIED, @@ -783,13 +785,29 @@ int dediprog_init(void) { struct usb_device *dev; - char *voltage, *device; + char *voltage, *device, *spispeed; + int spispeed_idx = 2; int millivolt = 3500; long usedevice = 0; - int ret; + int i, ret; msg_pspew("%s\n", __func__); + spispeed = extract_programmer_param("spispeed"); + if (spispeed) { + for (i = 0; spispeeds[i].name; ++i) { + if (!strcasecmp(spispeeds[i].name, spispeed)) { + spispeed_idx = i; + break; + } + } + if (!spispeeds[i].name) { + msg_perr("Error: Invalid 'spispeed' value.\n"); + free(spispeed); + return 1; + } + free(spispeed); + } voltage = extract_programmer_param("voltage"); if (voltage) { millivolt = parse_voltage(voltage); @@ -852,33 +870,24 @@ return 1; } dediprog_endpoint = 2; - + if (register_shutdown(dediprog_shutdown, NULL)) return 1; dediprog_set_leds(PASS_ON|BUSY_ON|ERROR_ON); - /* URB 6. Command A. */ - if (dediprog_command_a()) { + /* Perform basic setup. */ + if (dediprog_setup()) { dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return 1; } - /* URB 7. Command A. */ - if (dediprog_command_a()) { - dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); - return 1; - } - /* URB 8. Command Prepare Receive Device String. */ - /* URB 9. Command Receive Device String. */ - if (dediprog_check_devicestring()) { - dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); - return 1; - } - /* URB 10. Command C. */ - if (dediprog_command_c()) { + + /* After setting voltage and speed, perform setup again. */ + if (dediprog_set_spi_voltage(0) || dediprog_set_spi_speed(spispeed_idx) || dediprog_setup()) { dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); return 1; } + /* URB 11. Command Set SPI Voltage. */ if (dediprog_set_spi_voltage(millivolt)) { dediprog_set_leds(PASS_OFF|BUSY_OFF|ERROR_ON); Modified: trunk/flashrom.8 ============================================================================== --- trunk/flashrom.8 Mon Feb 4 05:38:42 2013 (r1648) +++ trunk/flashrom.8 Wed Feb 20 19:03:36 2013 (r1649) @@ -676,6 +676,18 @@ Usage example to select the second device: .sp .B " flashrom \-p dediprog:device=1" +.sp +An optional +.B spispeed +parameter specifies the frequency of the SPI bus. Syntax is +.sp +.B " flashrom \-p dediprog:spispeed=frequency" +.sp +where +.B frequency +can be +.BR 375k ", " 750k ", " 1.5M ", " 2.18M ", " 3M ", " 8M ", " 12M " or " 24M +(in Hz). The default is a frequency of 12 MHz. .SS .BR "rayer_spi " programmer The default I/O base address used for the parallel port is 0x378 and you can use

1 0

flashrom can never write if the flash chip isn't found automatically
by 123 123 Feb. 19, 2013

Feb. 19, 2013

1 0

W836xx: 03RG89 Ver FAB1: flashrom -V
by Don Alexander Feb. 19, 2013

Feb. 19, 2013

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 flashrom -V flashrom v0.9.5.2-r1546 on Linux 3.2.0-4-amd64 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.7, GCC 4.6.2, little endian Command line (1 args): flashrom -V Calibrating delay loop... OS timer resolution is 1 usecs, 3013M loops per second, 10 myus = 10 us, 100 myus = 115 us, 1000 myus = 991 us, 10000 myus = 10179 us, 4 myus = 12 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Dell Inc. " DMI string system-product-name: "Dell System XPS L702X" DMI string system-version: "Not Specified" DMI string baseboard-manufacturer: "Dell Inc. " DMI string baseboard-product-name: "03RG89" DMI string baseboard-version: "FAB1" DMI string chassis-type: "Portable" Laptop detected via DMI. W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 85. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found ITE EC, ID 0x8518,Rev 0x02 on port 0x4e. ======================================================================== WARNING! You seem to be running flashrom on an unsupported laptop. Laptops, notebooks and netbooks are difficult to support and we recommend to use the vendor flashing utility. The embedded controller (EC) in these machines often interacts badly with flashing. See http://www.flashrom.org/Laptops for details. If flash is shared with the EC, erase is guaranteed to brick your laptop and write may brick your laptop. Read and probe may irritate your EC and cause fan failure, backlight failure and sudden poweroff. You have been warned. ======================================================================== Aborting. - -- == Don Alexander It's a tough job, but some mug has to do it... RooSoft Ltd -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.12 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/ iEYEARECAAYFAlEi94cACgkQuipFNInZ6evyAACfWpcUW59YjP9xWE8uAttNQvw/ HP0AnRo5JGXUL4+mCVBRea2W861GexUh =H5wR -----END PGP SIGNATURE-----

1 0

Re: [flashrom] Please send a verbose log
by Eric Feb. 18, 2013

Feb. 18, 2013

Hi, Here is a verbose log for this : http://fr.asus.com/Motherboards/Intel_Socket_1155/P8P67M_PRO -- Si tu as une pomme, que j'ai une pomme, et que l'on échange nos pommes, nous aurons chacun une pomme. Mais si tu as une idée, que j'ai une idée, et que l'on échange nos idées, nous aurons chacun deux idées. La différence entre Linux et Windows ,c'est que Linux c'est comme une belle fille , il faut l'apprivoiser , la comprendre , la séduire tandis que Windows , c'est comme une prostitué , il faut payer et surtout bien se protéger. Pour remédier à ce problème, la solution c'est Ubuntu ! C'est une distribution GNU/Linux qui remplace avantageusement Ouinedoze. Vous êtes libre d'en obtenir une copie pour installation et utilisation en la téléchargeant gratuitement et légalement sur le lien ci-dessous. http://www.ubuntu-fr.org/telechargement

1 0

Re: [flashrom] Bypassing the size check
by Stefan Tauner Feb. 15, 2013

Feb. 15, 2013

On Thu, 14 Feb 2013 21:55:50 -0800 Jason Craik <jason.c7(a)gmail.com> wrote: > Hello, > > I'm trying to downgrade the bios on my Asus P8Z77-v LK motherboard and am > using a dos version of your program to try and do it. When I try and > reflash with the old .rom file it gives me an error about having two > different size files. I'm wondering if theres a way to just bypass that > check and force write the old .rom file onto the chip. Hello Jason, there is no command line switch to do this and there is no reason to do this in any sane use case either. How did you obtain the "old .rom file"? Obviously not by reading it with flashrom because then it would have the correct size. Also, P8Z77 sounds like a locked down board... please send a verbose log. I assume you have obtained an image of *the BIOS region only* by other means and want to write it to *the BIOS region only*... if you really know what you are doing, please take a look at the documentation of the layout file in the manpage and think about how you want to recover if something goes wrong. ;) -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Bypassing the size check
by Jason Craik Feb. 15, 2013

Feb. 15, 2013

Hello, I'm trying to downgrade the bios on my Asus P8Z77-v LK motherboard and am using a dos version of your program to try and do it. When I try and reflash with the old .rom file it gives me an error about having two different size files. I'm wondering if theres a way to just bypass that check and force write the old .rom file onto the chip. Thanks, Jason

1 0

flashrom for msi windpad 110w
by Seryi Kuznecov Feb. 13, 2013

Feb. 13, 2013

Hello! Need help knowing people. I have a tablet msi windpad 110w. For the Russian version of the producers put the trimmed version of the BIOS 207 http://paste.flashrom.org/view.php?id=1546 Roll back the standard means to version http://paste.flashrom.org/view.php?id=1547 by means ami msi and fails. The manufacturer says this to the fact that Russia banned TPM and therefore prohibited rollback bios and opening functions TPM (how unknown function in the BIOS to unlock the rollback not). The only way this is just the firmware programmer. It remains the last hope of flashrom. Here is a screen chip: http://paste.flashrom.org/view.php?id=1548. Datasheet: http://paste.flashrom.org/view.php?id=1549 Our version looks like 8-pin SOP (200mil, 150mil). Please help. Thank you.

1 0

Windpad 110w and flashrom
by Seryi Kuznecov Feb. 13, 2013

Feb. 13, 2013

Здравствуйте! Нужна помощь знающих людей. У меня планшет msi windpad 110w. Для российской версии производители поставили обрезанную версию биоса 207 http://paste.flashrom.org/view.php?id=1546 Откатить стандартными средствами на версию http://paste.flashrom.org/view.php?id=1547 с помощью средств ami и msi не получается. Производитель комментирует это тем, что в России запрещен TPM и поэтому запрещен откат биоса и открытие функций TPM (каким образом неизвестно, функции разлочки отката в биосе нет) . Единственный способ прошивки это только программатор. Остается последняя надежда на flashrom. Вот скрин чипа: http://paste.flashrom.org/view.php?id=1548. Даташит: http://paste.flashrom.org/view.php?id=1549 Наша версия похоже 8-pin SOP (200mil, 150mil). Прошу помощи. Спасибо.

1 0

[PATCH] total Makefile rewrite
by Carl-Daniel Hailfinger Feb. 13, 2013

Feb. 13, 2013

I almost lost my sanity trying to beat the Makefile into submission without using features only available in new GNU make versions. Some functions are now outsourced to a shell script. In theory, things should still work (except a few hardcoded dependencies which will be changed into autodetections in the future). At least now we have a framework to handle autodetection. It's not really hooked up yet, but it will allow stuff like make config CONFIG_WHATEVER=auto CONFIG_FOO=yes CONFIG_BAR=no The new (TM) way to compile flashrom is: make config make Please run "make distclean" the first time you test this patch. Not for merge yet, but this mechanism at least will allow clean handling of FTDI autodetect, libusb 1.x requirements and all that other pending fun stuff. Comments about the shell script are very appreciated, I tried to write in POSIX sh. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-Makefile_harddependencies_soft/hwaccess.h =================================================================== --- flashrom-Makefile_harddependencies_soft/hwaccess.h (Revision 1645) +++ flashrom-Makefile_harddependencies_soft/hwaccess.h (Arbeitskopie) @@ -167,7 +167,7 @@ #define le_to_cpu32 cpu_to_le32 #define le_to_cpu64 cpu_to_le64 -#if NEED_PCI == 1 +#if (NEED_PCI == 1) || (NEED_IOPORT_ACCESS == 1) #if defined (__i386__) || defined (__x86_64__) #define __FLASHROM_HAVE_OUTB__ 1 Index: flashrom-Makefile_harddependencies_soft/Makefile =================================================================== --- flashrom-Makefile_harddependencies_soft/Makefile (Revision 1645) +++ flashrom-Makefile_harddependencies_soft/Makefile (Arbeitskopie) @@ -103,28 +103,28 @@ LIBS += ../libgetopt/libgetopt.a # Bus Pirate, Serprog and PonyProg are not supported under DOS (missing serial support). ifeq ($(CONFIG_BUSPIRATE_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_BUSPIRATE_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_BUSPIRATE_SPI else override CONFIG_BUSPIRATE_SPI = no endif ifeq ($(CONFIG_SERPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_SERPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SERPROG else override CONFIG_SERPROG = no endif ifeq ($(CONFIG_PONY_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_PONY_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_PONY_SPI else override CONFIG_PONY_SPI = no endif # Dediprog and FT2232 are not supported under DOS (missing USB support). ifeq ($(CONFIG_DEDIPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_DEDIPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_DEDIPROG else override CONFIG_DEDIPROG = no endif ifeq ($(CONFIG_FT2232_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_FT2232_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_FT2232_SPI else override CONFIG_FT2232_SPI = no endif @@ -140,73 +140,73 @@ LDFLAGS += -L/usr/local/lib # Serprog is not supported under Windows/MinGW (missing sockets support). ifeq ($(CONFIG_SERPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_SERPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SERPROG else override CONFIG_SERPROG = no endif # For now we disable all PCI-based programmers on Windows/MinGW (no libpci). ifeq ($(CONFIG_INTERNAL), yes) -UNSUPPORTED_FEATURES += CONFIG_INTERNAL=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_INTERNAL else override CONFIG_INTERNAL = no endif ifeq ($(CONFIG_RAYER_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_RAYER_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_RAYER_SPI else override CONFIG_RAYER_SPI = no endif ifeq ($(CONFIG_NIC3COM), yes) -UNSUPPORTED_FEATURES += CONFIG_NIC3COM=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NIC3COM else override CONFIG_NIC3COM = no endif ifeq ($(CONFIG_GFXNVIDIA), yes) -UNSUPPORTED_FEATURES += CONFIG_GFXNVIDIA=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_GFXNVIDIA else override CONFIG_GFXNVIDIA = no endif ifeq ($(CONFIG_SATASII), yes) -UNSUPPORTED_FEATURES += CONFIG_SATASII=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SATASII else override CONFIG_SATASII = no endif ifeq ($(CONFIG_ATAHPT), yes) -UNSUPPORTED_FEATURES += CONFIG_ATAHPT=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_ATAHPT else override CONFIG_ATAHPT = no endif ifeq ($(CONFIG_DRKAISER), yes) -UNSUPPORTED_FEATURES += CONFIG_DRKAISER=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_DRKAISER else override CONFIG_DRKAISER = no endif ifeq ($(CONFIG_NICREALTEK), yes) -UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICREALTEK else override CONFIG_NICREALTEK = no endif ifeq ($(CONFIG_NICNATSEMI), yes) -UNSUPPORTED_FEATURES += CONFIG_NICNATSEMI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICNATSEMI else override CONFIG_NICNATSEMI = no endif ifeq ($(CONFIG_NICINTEL), yes) -UNSUPPORTED_FEATURES += CONFIG_NICINTEL=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICINTEL else override CONFIG_NICINTEL = no endif ifeq ($(CONFIG_NICINTEL_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_NICINTEL_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICINTEL_SPI else override CONFIG_NICINTEL_SPI = no endif ifeq ($(CONFIG_OGP_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_OGP_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_OGP_SPI else override CONFIG_OGP_SPI = no endif ifeq ($(CONFIG_SATAMV), yes) -UNSUPPORTED_FEATURES += CONFIG_SATAMV=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SATAMV else override CONFIG_SATAMV = no endif @@ -215,28 +215,28 @@ ifeq ($(TARGET_OS), libpayload) FLASHROM_CFLAGS += -DSTANDALONE ifeq ($(CONFIG_DUMMY), yes) -UNSUPPORTED_FEATURES += CONFIG_DUMMY=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_DUMMY else override CONFIG_DUMMY = no endif ifeq ($(CONFIG_BUSPIRATE_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_BUSPIRATE_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_BUSPIRATE_SPI else override CONFIG_BUSPIRATE_SPI = no endif ifeq ($(CONFIG_SERPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_SERPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SERPROG else override CONFIG_SERPROG = no endif # Dediprog and FT2232 are not supported with libpayload (missing libusb support) ifeq ($(CONFIG_DEDIPROG), yes) -UNSUPPORTED_FEATURES += CONFIG_DEDIPROG=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_DEDIPROG else override CONFIG_DEDIPROG = no endif ifeq ($(CONFIG_FT2232_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_FT2232_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_FT2232_SPI else override CONFIG_FT2232_SPI = no endif @@ -244,7 +244,7 @@ ifneq ($(TARGET_OS), Linux) ifeq ($(CONFIG_LINUX_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_LINUX_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_LINUX_SPI else override CONFIG_LINUX_SPI = no endif @@ -260,32 +260,32 @@ # Right now this means the drivers below only work on x86. ifneq ($(ARCH), x86) ifeq ($(CONFIG_NIC3COM), yes) -UNSUPPORTED_FEATURES += CONFIG_NIC3COM=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NIC3COM else override CONFIG_NIC3COM = no endif ifeq ($(CONFIG_NICREALTEK), yes) -UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICREALTEK else override CONFIG_NICREALTEK = no endif ifeq ($(CONFIG_NICNATSEMI), yes) -UNSUPPORTED_FEATURES += CONFIG_NICNATSEMI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_NICNATSEMI else override CONFIG_NICNATSEMI = no endif ifeq ($(CONFIG_RAYER_SPI), yes) -UNSUPPORTED_FEATURES += CONFIG_RAYER_SPI=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_RAYER_SPI else override CONFIG_RAYER_SPI = no endif ifeq ($(CONFIG_ATAHPT), yes) -UNSUPPORTED_FEATURES += CONFIG_ATAHPT=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_ATAHPT else override CONFIG_ATAHPT = no endif ifeq ($(CONFIG_SATAMV), yes) -UNSUPPORTED_FEATURES += CONFIG_SATAMV=yes +UNSUPPORTED_TARGET_FEATURES += CONFIG_SATAMV else override CONFIG_SATAMV = no endif @@ -411,6 +411,128 @@ ############################################################################### # Programmer drivers and programmer support infrastructure. +ifeq ($(CONFIG_INTERNAL), yes) +NEED_PCI += CONFIG_INTERNAL +endif + +ifeq ($(CONFIG_SERPROG), yes) +NEED_SERIAL += CONFIG_SERPROG +NEED_NET += CONFIG_SERPROG +endif + +ifeq ($(CONFIG_RAYER_SPI), yes) +NEED_IOPORT_ACCESS += CONFIG_RAYER_SPI +endif + +ifeq ($(CONFIG_PONY_SPI), yes) +NEED_SERIAL += CONFIG_PONY_SPI +endif + +ifeq ($(CONFIG_BITBANG_SPI), yes) +endif + +ifeq ($(CONFIG_NIC3COM), yes) +NEED_PCI += CONFIG_NIC3COM +endif + +ifeq ($(CONFIG_GFXNVIDIA), yes) +NEED_PCI += CONFIG_GFXNVIDIA +endif + +ifeq ($(CONFIG_SATASII), yes) +NEED_PCI += CONFIG_SATASII +endif + +ifeq ($(CONFIG_ATAHPT), yes) +NEED_PCI += CONFIG_ATAHPT +endif + +ifeq ($(CONFIG_FT2232_SPI), yes) +NEED_FTDI += CONFIG_FT2232_SPI +endif + +ifeq ($(CONFIG_DUMMY), yes) +endif + +ifeq ($(CONFIG_DRKAISER), yes) +NEED_PCI += CONFIG_DRKAISER +endif + +ifeq ($(CONFIG_NICREALTEK), yes) +NEED_PCI += CONFIG_NICREALTEK +endif + +ifeq ($(CONFIG_NICNATSEMI), yes) +NEED_PCI += CONFIG_NICNATSEMI +endif + +ifeq ($(CONFIG_NICINTEL), yes) +NEED_PCI += CONFIG_NICINTEL +endif + +ifeq ($(CONFIG_NICINTEL_SPI), yes) +NEED_PCI += CONFIG_NICINTEL_SPI +endif + +ifeq ($(CONFIG_OGP_SPI), yes) +NEED_PCI += CONFIG_OGP_SPI +endif + +ifeq ($(CONFIG_BUSPIRATE_SPI), yes) +NEED_SERIAL += CONFIG_BUSPIRATE_SPI +endif + +ifeq ($(CONFIG_DEDIPROG), yes) +NEED_USB += CONFIG_DEDIPROG +endif + +ifeq ($(CONFIG_SATAMV), yes) +NEED_PCI += CONFIG_SATAMV +endif + +ifeq ($(CONFIG_LINUX_SPI), yes) +endif + +ifneq ($(NEED_SERIAL), ) +endif + +ifneq ($(NEED_NET), ) +endif + +ifneq ($(NEED_PCI), ) +CHECK_LIBPCI = yes +endif + +ifneq ($(NEED_USB), ) +CHECK_LIBUSB0 = yes +endif + +ifneq ($(NEED_FTDI), ) +CHECK_LIBFTDI = yes +endif + +############################################################################################################################################################################# + +defaulttarget: all + +config: compiler + @printf "" > .availablefeatures + @./config.sh utsname +ifneq ($(CHECK_LIBPCI), ) + @./config.sh libpci +endif +ifneq ($(CHECK_LIBUSB0), ) + @./config.sh libusb0 +endif +ifeq ($(CHECK_LIBFTDI), yes) + @./config.sh libftdi +endif +ifeq ($(CONFIG_LINUX_SPI), yes) + @./config.sh linuxspi +endif + +-include .availablefeatures + FEATURE_CFLAGS += -D'CONFIG_DEFAULT_PROGRAMMER=$(CONFIG_DEFAULT_PROGRAMMER)' ifeq ($(CONFIG_INTERNAL), yes) @@ -421,27 +543,21 @@ PROGRAMMER_OBJS += ichspi.o ich_descriptors.o else endif -NEED_PCI := yes endif ifeq ($(CONFIG_SERPROG), yes) FEATURE_CFLAGS += -D'CONFIG_SERPROG=1' PROGRAMMER_OBJS += serprog.o -NEED_SERIAL := yes -NEED_NET := yes endif ifeq ($(CONFIG_RAYER_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_RAYER_SPI=1' PROGRAMMER_OBJS += rayer_spi.o -# Actually, NEED_PCI is wrong. NEED_IOPORT_ACCESS would be more correct. -NEED_PCI := yes endif ifeq ($(CONFIG_PONY_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_PONY_SPI=1' PROGRAMMER_OBJS += pony_spi.o -NEED_SERIAL := yes endif ifeq ($(CONFIG_BITBANG_SPI), yes) @@ -452,36 +568,29 @@ ifeq ($(CONFIG_NIC3COM), yes) FEATURE_CFLAGS += -D'CONFIG_NIC3COM=1' PROGRAMMER_OBJS += nic3com.o -NEED_PCI := yes endif ifeq ($(CONFIG_GFXNVIDIA), yes) FEATURE_CFLAGS += -D'CONFIG_GFXNVIDIA=1' PROGRAMMER_OBJS += gfxnvidia.o -NEED_PCI := yes endif ifeq ($(CONFIG_SATASII), yes) FEATURE_CFLAGS += -D'CONFIG_SATASII=1' PROGRAMMER_OBJS += satasii.o -NEED_PCI := yes endif ifeq ($(CONFIG_ATAHPT), yes) FEATURE_CFLAGS += -D'CONFIG_ATAHPT=1' PROGRAMMER_OBJS += atahpt.o -NEED_PCI := yes endif ifeq ($(CONFIG_FT2232_SPI), yes) -FTDILIBS := $(shell pkg-config --libs libftdi 2>/dev/null || printf "%s" "-lftdi -lusb") -# This is a totally ugly hack. -FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "FTDISUPPORT := yes" .features && printf "%s" "-D'CONFIG_FT2232_SPI=1'") -FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "FT232H := yes" .features && printf "%s" "-D'HAVE_FT232H=1'") -FEATURE_LIBS += $(shell LC_ALL=C grep -q "FTDISUPPORT := yes" .features && printf "%s" "$(FTDILIBS)") +FEATURE_CFLAGS += -D'CONFIG_FT2232_SPI=1' +ifeq ($(FT232H), yes) +FEATURE_CFLAGS += -D'HAVE_FT232H=1' +endif PROGRAMMER_OBJS += ft2232_spi.o -# We can't set NEED_USB here because that would transform libftdi auto-enabling -# into a hard requirement for libusb, defeating the purpose of auto-enabling. endif ifeq ($(CONFIG_DUMMY), yes) @@ -492,75 +601,64 @@ ifeq ($(CONFIG_DRKAISER), yes) FEATURE_CFLAGS += -D'CONFIG_DRKAISER=1' PROGRAMMER_OBJS += drkaiser.o -NEED_PCI := yes endif ifeq ($(CONFIG_NICREALTEK), yes) FEATURE_CFLAGS += -D'CONFIG_NICREALTEK=1' PROGRAMMER_OBJS += nicrealtek.o -NEED_PCI := yes endif ifeq ($(CONFIG_NICNATSEMI), yes) FEATURE_CFLAGS += -D'CONFIG_NICNATSEMI=1' PROGRAMMER_OBJS += nicnatsemi.o -NEED_PCI := yes endif ifeq ($(CONFIG_NICINTEL), yes) FEATURE_CFLAGS += -D'CONFIG_NICINTEL=1' PROGRAMMER_OBJS += nicintel.o -NEED_PCI := yes endif ifeq ($(CONFIG_NICINTEL_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_NICINTEL_SPI=1' PROGRAMMER_OBJS += nicintel_spi.o -NEED_PCI := yes endif ifeq ($(CONFIG_OGP_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_OGP_SPI=1' PROGRAMMER_OBJS += ogp_spi.o -NEED_PCI := yes endif ifeq ($(CONFIG_BUSPIRATE_SPI), yes) FEATURE_CFLAGS += -D'CONFIG_BUSPIRATE_SPI=1' PROGRAMMER_OBJS += buspirate_spi.o -NEED_SERIAL := yes endif ifeq ($(CONFIG_DEDIPROG), yes) FEATURE_CFLAGS += -D'CONFIG_DEDIPROG=1' PROGRAMMER_OBJS += dediprog.o -NEED_USB := yes endif ifeq ($(CONFIG_SATAMV), yes) FEATURE_CFLAGS += -D'CONFIG_SATAMV=1' PROGRAMMER_OBJS += satamv.o -NEED_PCI := yes endif ifeq ($(CONFIG_LINUX_SPI), yes) -# This is a totally ugly hack. -FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "LINUX_SPI_SUPPORT := yes" .features && printf "%s" "-D'CONFIG_LINUX_SPI=1'") +FEATURE_CFLAGS += -D'CONFIG_LINUX_SPI=1' PROGRAMMER_OBJS += linux_spi.o endif -ifeq ($(NEED_SERIAL), yes) +ifneq ($(NEED_SERIAL), ) LIB_OBJS += serial.o endif -ifeq ($(NEED_NET), yes) +ifneq ($(NEED_NET), ) ifeq ($(TARGET_OS), SunOS) LIBS += -lsocket endif endif -ifeq ($(NEED_PCI), yes) -CHECK_LIBPCI = yes +ifneq ($(NEED_PCI), ) FEATURE_CFLAGS += -D'NEED_PCI=1' PROGRAMMER_OBJS += pcidev.o physmap.o hwaccess.o ifeq ($(TARGET_OS), NetBSD) @@ -589,32 +687,45 @@ endif endif -ifeq ($(NEED_USB), yes) -CHECK_LIBUSB0 = yes +ifneq ($(NEED_USB), ) FEATURE_CFLAGS += -D'NEED_USB=1' USBLIBS := $(shell pkg-config --libs libusb 2>/dev/null || printf "%s" "-lusb") endif +ifneq ($(NEED_FTDI), ) +FEATURE_CFLAGS += -D'NEED_FTDI=1' +FTDILIBS := $(shell pkg-config --libs libftdi 2>/dev/null || libftdi-config --libs 2>/dev/null || printf "%s" "-lftdi") +endif + +ifneq ($(NEED_IOPORT_ACCESS), ) +FEATURE_CFLAGS += -D'NEED_IOPORT_ACCESS=1' +PROGRAMMER_OBJS += hwaccess.o +endif + ifeq ($(CONFIG_PRINT_WIKI), yes) FEATURE_CFLAGS += -D'CONFIG_PRINT_WIKI=1' CLI_OBJS += print_wiki.o endif -FEATURE_CFLAGS += $(shell LC_ALL=C grep -q "UTSNAME := yes" .features && printf "%s" "-D'HAVE_UTSNAME=1'") +ifeq ($(UTSNAME), yes) +FEATURE_CFLAGS += -D'HAVE_UTSNAME=1' +endif # We could use PULLED_IN_LIBS, but that would be ugly. -FEATURE_LIBS += $(shell LC_ALL=C grep -q "NEEDLIBZ := yes" .libdeps && printf "%s" "-lz") +ifeq ($(NEEDLIBZ), yes) +FEATURE_LIBS += -lz +endif -LIBFLASHROM_OBJS = $(CHIP_OBJS) $(PROGRAMMER_OBJS) $(LIB_OBJS) +LIBFLASHROM_OBJS = $(CHIP_OBJS) $(sort $(PROGRAMMER_OBJS)) $(LIB_OBJS) OBJS = $(CLI_OBJS) $(LIBFLASHROM_OBJS) -all: hwlibs features $(PROGRAM)$(EXEC_SUFFIX) +all: $(PROGRAM)$(EXEC_SUFFIX) ifeq ($(ARCH), x86) @+$(MAKE) -C util/ich_descriptors_tool/ TARGET_OS=$(TARGET_OS) EXEC_SUFFIX=$(EXEC_SUFFIX) endif $(PROGRAM)$(EXEC_SUFFIX): $(OBJS) - $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FEATURE_LIBS) $(LIBS) $(PCILIBS) $(USBLIBS) + $(CC) $(LDFLAGS) -o $(PROGRAM)$(EXEC_SUFFIX) $(OBJS) $(FTDILIBS) $(USBLIBS) $(PCILIBS) $(FEATURE_LIBS) $(LIBS) libflashrom.a: $(LIBFLASHROM_OBJS) $(AR) rcs $@ $^ @@ -625,7 +736,11 @@ # stored files, they can be handled here as well. TAROPTIONS = $(shell LC_ALL=C tar --version|grep -q GNU && echo "--owner=root --group=root") -%.o: %.c .features +%.o: %.c +ifeq ($(wildcard .availablefeatures), ) + @echo 'You have to run "make config" first' + @false +endif $(CC) -MMD $(CFLAGS) $(CPPFLAGS) $(FLASHROM_CFLAGS) $(FEATURE_CFLAGS) $(SVNDEF) -o $@ -c $< # Make sure to add all names of generated binaries here. @@ -636,7 +751,7 @@ @+$(MAKE) -C util/ich_descriptors_tool/ clean distclean: clean - rm -f .features .libdeps + rm -f .availablefeatures strip: $(PROGRAM)$(EXEC_SUFFIX) $(STRIP) $(STRIP_ARGS) $(PROGRAM)$(EXEC_SUFFIX) @@ -699,60 +814,6 @@ endef export LIBUSB0_TEST -hwlibs: compiler - @printf "" > .libdeps -ifeq ($(CHECK_LIBPCI), yes) - @printf "Checking for libpci headers... " - @echo "$$LIBPCI_TEST" > .test.c - @$(CC) -c $(CPPFLAGS) $(CFLAGS) .test.c -o .test.o >/dev/null && \ - echo "found." || ( echo "not found."; echo; \ - echo "Please install libpci headers (package pciutils-devel)."; \ - echo "See README for more information."; echo; \ - rm -f .test.c .test.o; exit 1) - @printf "Checking if libpci is present and sufficient... " - @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) $(PCILIBS) >/dev/null && \ - echo "yes." || ( echo "no."; \ - printf "Checking if libz+libpci are present and sufficient..."; \ - $(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) $(PCILIBS) -lz >/dev/null && \ - ( echo "yes."; echo "NEEDLIBZ := yes" > .libdeps ) || ( echo "no."; echo; \ - echo "Please install libpci (package pciutils) and/or libz."; \ - echo "See README for more information."; echo; \ - rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) ) - @rm -f .test.c .test.o .test$(EXEC_SUFFIX) -endif -ifeq ($(CHECK_LIBUSB0), yes) - @printf "Checking for libusb-0.1/libusb-compat headers... " - @echo "$$LIBUSB0_TEST" > .test.c - @$(CC) -c $(CPPFLAGS) $(CFLAGS) .test.c -o .test.o >/dev/null && \ - echo "found." || ( echo "not found."; echo; \ - echo "Please install libusb-0.1 headers or libusb-compat headers."; \ - echo "See README for more information."; echo; \ - rm -f .test.c .test.o; exit 1) - @printf "Checking if libusb-0.1 is usable... " - @$(CC) $(LDFLAGS) .test.o -o .test$(EXEC_SUFFIX) $(LIBS) $(USBLIBS) >/dev/null && \ - echo "yes." || ( echo "no."; \ - echo "Please install libusb-0.1 or libusb-compat."; \ - echo "See README for more information."; echo; \ - rm -f .test.c .test.o .test$(EXEC_SUFFIX); exit 1) - @rm -f .test.c .test.o .test$(EXEC_SUFFIX) -endif - -.features: features - -# If a user does not explicitly request a non-working feature, we should -# silently disable it. However, if a non-working (does not compile) feature -# is explicitly requested, we should bail out with a descriptive error message. -# We also have to check that at least one programmer driver is enabled. -featuresavailable: -ifeq ($(PROGRAMMER_OBJS),) - @echo "You have to enable at least one programmer driver!" - @false -endif -ifneq ($(UNSUPPORTED_FEATURES), ) - @echo "The following features are unavailable on your machine: $(UNSUPPORTED_FEATURES)" - @false -endif - define FTDI_TEST #include <ftdi.h> struct ftdi_context *ftdic = NULL; @@ -771,60 +832,47 @@ endef export FTDI_232H_TEST -define UTSNAME_TEST -#include <sys/utsname.h> -struct utsname osinfo; +define LINUX_SPI_TEST +#include <linux/types.h> +#include <linux/spi/spidev.h> + int main(int argc, char **argv) { (void) argc; (void) argv; - uname (&osinfo); return 0; } endef -export UTSNAME_TEST +export LINUX_SPI_TEST -define LINUX_SPI_TEST -#include <linux/types.h> -#include <linux/spi/spidev.h> - +define UTSNAME_TEST +#include <sys/utsname.h> +struct utsname osinfo; int main(int argc, char **argv) { (void) argc; (void) argv; + uname (&osinfo); return 0; } endef -export LINUX_SPI_TEST +export UTSNAME_TEST -features: compiler - @echo "FEATURES := yes" > .features.tmp -ifeq ($(CONFIG_FT2232_SPI), yes) - @printf "Checking for FTDI support... " - @echo "$$FTDI_TEST" > .featuretest.c - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ - ( echo "found."; echo "FTDISUPPORT := yes" >> .features.tmp ) || \ - ( echo "not found."; echo "FTDISUPPORT := no" >> .features.tmp ) - @printf "Checking for FT232H support in libftdi... " - @echo "$$FTDI_232H_TEST" >> .featuretest.c - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) $(FTDILIBS) $(LIBS) >/dev/null 2>&1 && \ - ( echo "found."; echo "FT232H := yes" >> .features.tmp ) || \ - ( echo "not found."; echo "FT232H := no" >> .features.tmp ) +export CC + +# If a user does not explicitly request a non-working feature, we should +# silently disable it. However, if a non-working (does not compile) feature +# is explicitly requested, we should bail out with a descriptive error message. +# We also have to check that at least one programmer driver is enabled. +featuresavailable: +ifeq ($(PROGRAMMER_OBJS),) + @echo "You have to enable at least one programmer driver!" + @false endif -ifeq ($(CONFIG_LINUX_SPI), yes) - @printf "Checking if Linux SPI headers are present... " - @echo "$$LINUX_SPI_TEST" > .featuretest.c - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) >/dev/null 2>&1 && \ - ( echo "yes."; echo "LINUX_SPI_SUPPORT := yes" >> .features.tmp ) || \ - ( echo "no."; echo "LINUX_SPI_SUPPORT := no" >> .features.tmp ) +ifneq ($(UNSUPPORTED_TARGET_FEATURES), ) + @echo "The following features are unavailable on the target machine: $(UNSUPPORTED_TARGET_FEATURES)" + @false endif - @printf "Checking for utsname support... " - @echo "$$UTSNAME_TEST" > .featuretest.c - @$(CC) $(CPPFLAGS) $(CFLAGS) $(LDFLAGS) .featuretest.c -o .featuretest$(EXEC_SUFFIX) >/dev/null 2>&1 && \ - ( echo "found."; echo "UTSNAME := yes" >> .features.tmp ) || \ - ( echo "not found."; echo "UTSNAME := no" >> .features.tmp ) - @$(DIFF) -q .features.tmp .features >/dev/null 2>&1 && rm .features.tmp || mv .features.tmp .features - @rm -f .featuretest.c .featuretest$(EXEC_SUFFIX) install: $(PROGRAM)$(EXEC_SUFFIX) mkdir -p $(DESTDIR)$(PREFIX)/sbin @@ -849,6 +897,10 @@ libpayload: clean make CC="CC=i386-elf-gcc lpgcc" AR=i386-elf-ar RANLIB=i386-elf-ranlib -.PHONY: all clean distclean compiler hwlibs features export tarball dos featuresavailable +.PHONY: all clean distclean compiler config export tarball dos featuresavailable +.EXPORT_ALL_VARIABLES: + +-include .availablefeatures + -include $(OBJS:.o=.d) Index: flashrom-Makefile_harddependencies_soft/config.sh =================================================================== --- flashrom-Makefile_harddependencies_soft/config.sh (Revision 0) +++ flashrom-Makefile_harddependencies_soft/config.sh (Revision 0) @@ -0,0 +1,199 @@ +#!/bin/sh +libpci() { + printf "Checking for libpci headers... " + echo "$LIBPCI_TEST" > .test.c + ${CC} -c ${CPPFLAGS} ${CFLAGS} .test.c -o .test.o >.testresult 2>&1 && { + echo "found." + } || { + echo "not found." + if [ ${CHECK_LIBPCI} = yes ]; then + echo + echo "Please install libpci headers (package pciutils-devel)" + echo "or disable the following features: ${NEED_PCI}" + echo "See README for more information." + echo + rm -f .test.o + exit 1 + else + for a in ${NEED_PCI}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_PCI}" + echo "See README for more information." + echo + rm -f .test.c .test.o + return 0 + fi + } + printf "Checking if libpci is present and sufficient... " + ${CC} ${LDFLAGS} .test.o -o .test${EXEC_SUFFIX} ${PCILIBS} ${LIBS} >.testresult 2>&1 && { + echo "yes." + } || { + echo "no." + printf "Checking if libz+libpci are present and sufficient..." + ${CC} ${LDFLAGS} .test.o -o .test${EXEC_SUFFIX} ${PCILIBS} -lz ${LIBS} >.testresult 2>&1 && { + echo "yes." + echo "NEEDLIBZ := yes" > .availablefeatures + } || { + echo "no." + if [ ${CHECK_LIBPCI} = yes ]; then + echo + echo "Please install libpci (package pciutils) and/or libz" + echo "or disable the following features: ${NEED_PCI}" + echo "See README for more information." + echo + rm -f test.o .test${EXEC_SUFFIX} + exit 1 + else + for a in ${NEED_PCI}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_PCI}" + echo "See README for more information." + echo + rm -f .test.c .test.o; .test${EXEC_SUFFIX} + return 0 + fi + } + } + rm -f .test.c .test.o .test${EXEC_SUFFIX} .testresult +} + +libusb0() { + printf "Checking for libusb-0.1/libusb-compat headers... " + echo "$LIBUSB0_TEST" > .test.c + ${CC} -c ${CPPFLAGS} ${CFLAGS} .test.c -o .test.o >.testresult 2>&1 && { + echo "found." + } || { + echo "not found." + if [ ${CHECK_LIBUSB0} = yes ]; then + echo + echo "Please install libusb-0.1 headers or libusb-compat headers" + echo "or disable the following features: ${NEED_USB}" + echo "See README for more information." + echo + rm -f .test.o + exit 1 + else + for a in ${NEED_USB}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_USB}" + echo "See README for more information." + echo + rm -f .test.c .test.o + return 0 + fi + } + printf "Checking if libusb-0.1/libusb-compat is usable... " + ${CC} ${LDFLAGS} .test.o -o .test${EXEC_SUFFIX} ${USBLIBS} ${LIBS} >.testresult 2>&1 && { + echo "yes." + } || { + echo "no." + if [ ${CHECK_LIBUSB0} = yes ]; then + echo + echo "Please install libusb-0.1 or libusb-compat" + echo "or disable the following features: ${NEED_USB}" + echo "See README for more information." + echo + rm -f .test.o .test${EXEC_SUFFIX} + exit 1 + else + for a in ${NEED_USB}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_USB}" + echo "See README for more information." + echo + rm -f .test.c .test.o + return 0 + fi + } + rm -f .test.c .test.o .test${EXEC_SUFFIX} .testresult +} + +libftdi() { + printf "Checking for libftdi support... " + echo "$FTDI_TEST" > .test.c + ${CC} ${CPPFLAGS} ${CFLAGS} ${LDFLAGS} .test.c -o .test${EXEC_SUFFIX} ${FTDILIBS} ${LIBS} >.testresult 2>&1 && { + echo "found." + } || { + echo "not found." + if [ ${CHECK_LIBFTDI} = yes ]; then + echo + echo "Please install libftdi headers" + echo "or disable the following features: ${NEED_FTDI}" + echo "See README for more information." + echo + rm -f .test${EXEC_SUFFIX} + exit 1 + else + for a in ${NEED_FTDI}; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: ${NEED_FTDI}" + echo "See README for more information." + echo + rm -f .test.c .test${EXEC_SUFFIX} + return 0 + fi + } + printf "Checking for FT232H support in libftdi... " + echo "$FTDI_232H_TEST" >> .test.c + ${CC} ${CPPFLAGS} ${CFLAGS} ${LDFLAGS} .test.c -o .test${EXEC_SUFFIX} ${FTDILIBS} ${LIBS} >.testresult 2>&1 && { + echo "found." + echo "FT232H := yes" >> .availablefeatures + } || { + echo "not found." + } + rm -f .test.c .test${EXEC_SUFFIX} .testresult +} + +linuxspi() { + printf "Checking for Linux kernel SPI headers... " + echo "$LINUX_SPI_TEST" > .test.c + ${CC} ${CPPFLAGS} ${CFLAGS} ${LDFLAGS} .test.c -o .test${EXEC_SUFFIX} >.testresult 2>&1 && { + echo "found." + } || { + echo "not found." + if [ ${CONFIG_LINUX_SPI} = yes ]; then + echo + echo "Please install Linux kernel SPI headers (linux/spi/spidev.h, part of recent glibc)" + echo "or disable the following features: CONFIG_LINUX_SPI" + echo "See README for more information." + echo + rm -f .test${EXEC_SUFFIX} + exit 1 + else + for a in CONFIG_LINUX_SPI; do + echo "${a} := no" >> .availablefeatures + done + echo + echo "The following features have been automatically disabled: CONFIG_LINUX_SPI" + echo "See README for more information." + echo + rm -f .test.c .test${EXEC_SUFFIX} + return 0 + fi + } + rm -f .test.c .test${EXEC_SUFFIX} .testresult +} + +utsname() { + printf "Checking for utsname support... " + echo "$UTSNAME_TEST" > .test.c + ${CC} ${CPPFLAGS} ${CFLAGS} ${LDFLAGS} .test.c -o .test${EXEC_SUFFIX} >/dev/null 2>&1 && { + echo "found." + echo "UTSNAME := yes" >> .availablefeatures + } || { + echo "not found." + } + rm -f .test.c .test${EXEC_SUFFIX} .testresult +} + +eval $1 Eigenschaftsänderungen: flashrom-Makefile_harddependencies_soft/config.sh ___________________________________________________________________ Hinzugefügt: svn:executable + * -- http://www.hailfinger.org/

1 1

Report: Intel DQ77KB KBQ7710H.86A.0049.2013.0130.1732 write
by dpcimanager＠users.sourceforge.net Feb. 12, 2013

Feb. 12, 2013

flashrom v0.9.6.1-r1646 on Darwin 12.2.0 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.10, LLVM Clang 4.1 ((tags/Apple/clang-421.11.66)), little endian Command line (5 args): /Volumes/USB/[Megafileupload]DPCIManager/DPCIManager.app/Contents/MacOS/flashrom -VV -w /var/folders/0g/vk1bx8k94r7_3_p_tllzvqvm0000gn/T/DPCIcw3meF.rom -p internal Calibrating delay loop... OS timer resolution is 1 usecs, 459M loops per second, 10 myus = 12 us, 100 myus = 102 us, 1000 myus = 1028 us, 10000 myus = 10668 us, 4 myus = 4 us, OK. Initializing internal programmer Mapping low megabyte at 0x00000400, unaligned size 0xffc00. Mapping low megabyte, 0xffc00 bytes at unaligned 0x00000400. No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "Intel Corporation" DMI string baseboard-product-name: "DQ77KB" DMI string baseboard-version: "AAG40294-401" DMI string chassis-type: "Desktop" Found chipset "Intel Q77" with PCI ID 8086:1e47. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes BIOS_CNTL = 0x2a: BIOS Lock Enable: enabled, BIOS Write Enable: disabled Warning: BIOS region SMM protection is enabled! Warning: Setting Bios Control at 0xdc from 0x2a to 0x0b on Q77 failed. New value is 0x2a. Root Complex Register Block address = 0xfed1c000 GCS = 0xc61: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 Warning: SPI Configuration Lockdown activated. Reading OPCODES... done OP Type Pre-OP op[0]: 0x02, write w/ addr, none op[1]: 0x03, read w/ addr, none op[2]: 0x20, write w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x9f, read w/o addr, none op[5]: 0x01, write w/o addr, none op[6]: 0x00, read w/o addr, none op[7]: 0x00, read w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x00 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00000000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x0bff05c0 FREG1: BIOS region (0x005c0000-0x00bfffff) is read-write. 0x5C: 0x05bf0003 FREG2: Warning: Management Engine region (0x00003000-0x005bffff) is locked. 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write. 0x64: 0x00001fff FREG4: Platform Data region is unused. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled for safety reasons. You can enforce write support with the ich_spi_force programmer option, but you will most likely harm your hardware! If you force flashrom you will get no support if something breaks. On a few mainboards it is possible to enable write access by setting a jumper (see its documentation or the board itself). 0x90: 0x80 (SSFS) SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0 0x91: 0xf94010 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=0, SME=0, SCF=1 0x94: 0x0006 (PREOP) 0x96: 0x043b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0000019f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x03040103 FLMAP1 0x12100206 FLMAP2 0x00210120 --- Details --- NR (Number of Regions): 4 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 2 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x0930001c FLILL 0x00000000 --- Details --- Component 1 density: 8 MB Component 2 density: 4 MB Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 33 MHz Write and Erase Clock Freq.: 33 MHz Fast Read is supported. Fast Read Clock Frequency: 33 MHz No forbidden opcodes. === Region Section === FLREG0 0x00000000 FLREG1 0x0bff05c0 FLREG2 0x05bf0003 FLREG3 0x00020001 FLREG4 0x00001fff --- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x005c0000 - 0x00bfffff Region 2 (ME ) 0x00003000 - 0x005bffff Region 3 (GbE ) 0x00001000 - 0x00002fff Region 4 (Platf.) is unused. === Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08080118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE rw Enabling hardware sequencing due to multiple flash chips detected. SPI Read Configuration: prefetching enabled, caching enabled, PROBLEMS, continuing anyway The following protocols are supported: FWH, Programmer-specific. Probing for Programmer Opaque flash chip, 0 kB: Found 2 attached SPI flash chips with a combined density of 12288 kB. There is only one partition containing the whole address space (0x000000 - 0xbfffff). There are 3072 erase blocks with 4096 B each. Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific) at physical address 0x0. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific). Write/erase is not working yet on your programmer in its current configuration. Aborting. Restoring MMIO space at 0x10ef718a0 Restoring PCI config space for 00:1f:0 reg 0xdc

1 0

Re: [flashrom] Fwd: BIOS Write Enable bit problem.
by Andrew Goodbody Feb. 11, 2013

Feb. 11, 2013

On 10/02/13 00:45, Rich Futyma wrote: > Would happen to know which linux driver handles this interrupt? SMM code is loaded into SMRAM during BIOS POST. Then the access to SMRAM is locked so that SMRAM is only visible when an SMI is active. The CPU cannot access SMRAM when no SMI is active. The CPU immediately starts to execute code from SMRAM once it receives the SMI. There is no Linux code involved, this is all initialised before any OS code is loaded. > Also, do you know where is this "correct handshake" described? It seems > that once bit 1 is set it can only be cleared by the reset. No. This handshake is not public knowledge AFAIK. It would not be much of a protection mechanism if everyone, including the virus writers, knew how to bypass it. I would expect the handshake to involve cryptography as well. Andrew

2 1

Re: [flashrom] a serious problem to solve
by Idwer Vollering Feb. 10, 2013

Feb. 10, 2013

2013/2/10 Henry Blanco Lores <hblanco2009(a)gmail.com>: > Hi Idwer, do you finally have any idea if the problem could be solved? > Henry Pleasse read, and reply to, the mailinglist for questions, don't reply to me or others without adding flashrom(a)flashrom.org to To: or Cc:. Thanks :) http://www.coreboot.org/pipermail/flashrom/2013-February/thread.html#10519 >>> > _______________________________________________ >>> > flashrom mailing list >>> > flashrom(a)flashrom.org >>> > http://www.flashrom.org/mailman/listinfo/flashrom >> >> >

1 0

Re: [flashrom] Fwd: BIOS Write Enable bit problem.
by Andrew Goodbody Feb. 10, 2013

Feb. 10, 2013

On 08/02/13 23:47, Rich Futyma wrote: > Does anyone know why bit 0 in the BIOS Control register cannot be set using > Intel® X79 Express Chipset. This is what I get when running: > flashrom -r /tmp/bios.rom -p internal or flashrom -w xx.rom -p internal > > *Warning: Setting Bios Control at 0xdc from 0x2a to 0x0b on X79 failed.* > *New value is 0x2a.* You can see that bit 1 is already set. This will generate an SMI when you attempt to set bit 0. There will be SMM code that will reset bit 0 if you have not performed the correct handshake beforehand. This is a protection mechanism to prevent unauthorised modification of the BIOS. Andrew

2 1

chipset "NVIDIA MCP78S"
by Алексей Кардапольцев Feb. 9, 2013

Feb. 9, 2013

You're asking for email a report to flashrom(a)flashrom.org including a verbose (-V) log. Here it is: ┌─[~] └─[alexey@home]: sudo flashrom -V -w 1402.BIN flashrom v0.9.5.2-r1546 on Linux 3.2.0-4-amd64 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.7, GCC 4.6.2, little endian Command line (3 args): flashrom -V -w 1402.BIN Calibrating delay loop... OS timer resolution is 1 usecs, 402M loops per second, delay more than 10% too short (got 37% of expected delay), recalculating... 324M loops per second, delay more than 10% too short (got 29% of expected delay), recalculating... 327M loops per second, delay more than 10% too short (got 30% of expected delay), recalculating... 327M loops per second, delay more than 10% too short (got 30% of expected delay), recalculating... 328M loops per second, delay loop is unreliable, trying to continue 10 myus = 3 us, 100 myus = 30 us, 1000 myus = 298 us, 10000 myus = 9494 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M3N78 PRO" DMI string baseboard-version: "1.XX" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8716 on port 0x2e Found chipset "NVIDIA MCP78S" with PCI ID 10de:075c. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 Flash bus type is SPI SPI on this chipset is WIP. Please report any success or failure by mailing us the verbose output to flashrom(a)flashrom.org, thanks! Found SMBus device 10de:0752 at 00:01:1 MCP SPI BAR is at 0xfdf80000 Mapping NVIDIA MCP6x SPI at 0xfdf80000, unaligned size 0x544. SPI control is 0xc012, req=0, gnt=0 Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. No IT87* serial flash segment enabled. The following protocols are supported: SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Chip status register is 00 Found Eon flash chip "EN25F80" (1024 kB, SPI) at physical address 0xfff00000. Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for GigaDevice GD25Q20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for GigaDevice GD25Q40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for GigaDevice GD25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for GigaDevice GD25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for GigaDevice GD25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for GigaDevice GD25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for GigaDevice GD25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Numonyx N25Q064, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for SST SST25LF040A, 512 kB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0x1c, id2 0x13 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0x1c, id2 0x13 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0x1c, id2 0x13 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Unknown SFDP-capable chip, 0 kB: No SFDP signature found. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0x1c, id2 0x3114 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0x1c, id2 0x13 Found Eon flash chip "EN25F80" (1024 kB, SPI). Flash image seems to be a legacy BIOS. Disabling coreboot-related checks. Reading old flash chip contents... done. Erasing and writing flash chip... Trying erase function 0... 0x000000-0x000fff:EW, 0x001000-0x001fff:E, 0x002000-0x002fff:S, 0x003000-0x003fff:S, 0x004000-0x004fff:S, 0x005000-0x005fff:S, 0x006000-0x006fff:S, 0x007000-0x007fff:S, 0x008000-0x008fff:S, 0x009000-0x009fff:S, 0x00a000-0x00afff:S, 0x00b000-0x00bfff:S, 0x00c000-0x00cfff:S, 0x00d000-0x00dfff:S, 0x00e000-0x00efff:S, 0x00f000-0x00ffff:S, 0x010000-0x010fff:S, 0x011000-0x011fff:E, 0x012000-0x012fff:S, 0x013000-0x013fff:S, 0x014000-0x014fff:S, 0x015000-0x015fff:S, 0x016000-0x016fff:S, 0x017000-0x017fff:S, 0x018000-0x018fff:S, 0x019000-0x019fff:S, 0x01a000-0x01afff:S, 0x01b000-0x01bfff:S, 0x01c000-0x01cfff:S, 0x01d000-0x01dfff:S, 0x01e000-0x01efff:S, 0x01f000-0x01ffff:S, 0x020000-0x020fff:EW, 0x021000-0x021fff:EW, 0x022000-0x022fff:EW, 0x023000-0x023fff:EW, 0x024000-0x024fff:EW, 0x025000-0x025fff:EW, 0x026000-0x026fff:EW, 0x027000-0x027fff:EW, 0x028000-0x028fff:EW, 0x029000-0x029fff:EW, 0x02a000-0x02afff:EW, 0x02b000-0x02bfff:EW, 0x02c000-0x02cfff:EW, 0x02d000-0x02dfff:EW, 0x02e000-0x02efff:EW, 0x02f000-0x02ffff:EW, 0x030000-0x030fff:EW, 0x031000-0x031fff:EW, 0x032000-0x032fff:EW, 0x033000-0x033fff:EW, 0x034000-0x034fff:EW, 0x035000-0x035fff:EW, 0x036000-0x036fff:EW, 0x037000-0x037fff:EW, 0x038000-0x038fff:EW, 0x039000-0x039fff:EW, 0x03a000-0x03afff:EW, 0x03b000-0x03bfff:EW, 0x03c000-0x03cfff:EW, 0x03d000-0x03dfff:EW, 0x03e000-0x03efff:EW, 0x03f000-0x03ffff:EW, 0x040000-0x040fff:EW, 0x041000-0x041fff:EW, 0x042000-0x042fff:EW, 0x043000-0x043fff:EW, 0x044000-0x044fff:EW, 0x045000-0x045fff:EW, 0x046000-0x046fff:EW, 0x047000-0x047fff:EW, 0x048000-0x048fff:EW, 0x049000-0x049fff:EW, 0x04a000-0x04afff:EW, 0x04b000-0x04bfff:EW, 0x04c000-0x04cfff:EW, 0x04d000-0x04dfff:EW, 0x04e000-0x04efff:EW, 0x04f000-0x04ffff:EW, 0x050000-0x050fff:EW, 0x051000-0x051fff:EW, 0x052000-0x052fff:EW, 0x053000-0x053fff:EW, 0x054000-0x054fff:EW, 0x055000-0x055fff:EW, 0x056000-0x056fff:EW, 0x057000-0x057fff:EW, 0x058000-0x058fff:EW, 0x059000-0x059fff:EW, 0x05a000-0x05afff:EW, 0x05b000-0x05bfff:EW, 0x05c000-0x05cfff:EW, 0x05d000-0x05dfff:EW, 0x05e000-0x05efff:EW, 0x05f000-0x05ffff:EW, 0x060000-0x060fff:EW, 0x061000-0x061fff:EW, 0x062000-0x062fff:EW, 0x063000-0x063fff:EW, 0x064000-0x064fff:EW, 0x065000-0x065fff:EW, 0x066000-0x066fff:EW, 0x067000-0x067fff:EW, 0x068000-0x068fff:EW, 0x069000-0x069fff:EW, 0x06a000-0x06afff:EW, 0x06b000-0x06bfff:EW, 0x06c000-0x06cfff:EW, 0x06d000-0x06dfff:EW, 0x06e000-0x06efff:EW, 0x06f000-0x06ffff:EW, 0x070000-0x070fff:EW, 0x071000-0x071fff:EW, 0x072000-0x072fff:EW, 0x073000-0x073fff:EW, 0x074000-0x074fff:EW, 0x075000-0x075fff:EW, 0x076000-0x076fff:EW, 0x077000-0x077fff:EW, 0x078000-0x078fff:EW, 0x079000-0x079fff:EW, 0x07a000-0x07afff:EW, 0x07b000-0x07bfff:EW, 0x07c000-0x07cfff:EW, 0x07d000-0x07dfff:EW, 0x07e000-0x07efff:EW, 0x07f000-0x07ffff:EW, 0x080000-0x080fff:EW, 0x081000-0x081fff:EW, 0x082000-0x082fff:EW, 0x083000-0x083fff:EW, 0x084000-0x084fff:EW, 0x085000-0x085fff:EW, 0x086000-0x086fff:EW, 0x087000-0x087fff:EW, 0x088000-0x088fff:EW, 0x089000-0x089fff:EW, 0x08a000-0x08afff:EW, 0x08b000-0x08bfff:EW, 0x08c000-0x08cfff:EW, 0x08d000-0x08dfff:EW, 0x08e000-0x08efff:EW, 0x08f000-0x08ffff:EW, 0x090000-0x090fff:EW, 0x091000-0x091fff:EW, 0x092000-0x092fff:EW, 0x093000-0x093fff:EW, 0x094000-0x094fff:EW, 0x095000-0x095fff:EW, 0x096000-0x096fff:EW, 0x097000-0x097fff:EW, 0x098000-0x098fff:EW, 0x099000-0x099fff:EW, 0x09a000-0x09afff:EW, 0x09b000-0x09bfff:EW, 0x09c000-0x09cfff:EW, 0x09d000-0x09dfff:EW, 0x09e000-0x09efff:EW, 0x09f000-0x09ffff:EW, 0x0a0000-0x0a0fff:EW, 0x0a1000-0x0a1fff:EW, 0x0a2000-0x0a2fff:E, 0x0a3000-0x0a3fff:E, 0x0a4000-0x0a4fff:E, 0x0a5000-0x0a5fff:E, 0x0a6000-0x0a6fff:E, 0x0a7000-0x0a7fff:S, 0x0a8000-0x0a8fff:S, 0x0a9000-0x0a9fff:S, 0x0aa000-0x0aafff:S, 0x0ab000-0x0abfff:S, 0x0ac000-0x0acfff:S, 0x0ad000-0x0adfff:S, 0x0ae000-0x0aefff:S, 0x0af000-0x0affff:S, 0x0b0000-0x0b0fff:S, 0x0b1000-0x0b1fff:S, 0x0b2000-0x0b2fff:S, 0x0b3000-0x0b3fff:S, 0x0b4000-0x0b4fff:S, 0x0b5000-0x0b5fff:S, 0x0b6000-0x0b6fff:S, 0x0b7000-0x0b7fff:S, 0x0b8000-0x0b8fff:S, 0x0b9000-0x0b9fff:S, 0x0ba000-0x0bafff:S, 0x0bb000-0x0bbfff:S, 0x0bc000-0x0bcfff:S, 0x0bd000-0x0bdfff:S, 0x0be000-0x0befff:S, 0x0bf000-0x0bffff:S, 0x0c0000-0x0c0fff:S, 0x0c1000-0x0c1fff:S, 0x0c2000-0x0c2fff:S, 0x0c3000-0x0c3fff:S, 0x0c4000-0x0c4fff:S, 0x0c5000-0x0c5fff:S, 0x0c6000-0x0c6fff:S, 0x0c7000-0x0c7fff:S, 0x0c8000-0x0c8fff:S, 0x0c9000-0x0c9fff:S, 0x0ca000-0x0cafff:S, 0x0cb000-0x0cbfff:S, 0x0cc000-0x0ccfff:S, 0x0cd000-0x0cdfff:S, 0x0ce000-0x0cefff:S, 0x0cf000-0x0cffff:S, 0x0d0000-0x0d0fff:S, 0x0d1000-0x0d1fff:S, 0x0d2000-0x0d2fff:S, 0x0d3000-0x0d3fff:S, 0x0d4000-0x0d4fff:S, 0x0d5000-0x0d5fff:S, 0x0d6000-0x0d6fff:S, 0x0d7000-0x0d7fff:S, 0x0d8000-0x0d8fff:S, 0x0d9000-0x0d9fff:S, 0x0da000-0x0dafff:W, 0x0db000-0x0dbfff:W, 0x0dc000-0x0dcfff:W, 0x0dd000-0x0ddfff:W, 0x0de000-0x0defff:W, 0x0df000-0x0dffff:W, 0x0e0000-0x0e0fff:EW, 0x0e1000-0x0e1fff:EW, 0x0e2000-0x0e2fff:EW, 0x0e3000-0x0e3fff:EW, 0x0e4000-0x0e4fff:EW, 0x0e5000-0x0e5fff:EW, 0x0e6000-0x0e6fff:EW, 0x0e7000-0x0e7fff:EW, 0x0e8000-0x0e8fff:EW, 0x0e9000-0x0e9fff:EW, 0x0ea000-0x0eafff:EW, 0x0eb000-0x0ebfff:EW, 0x0ec000-0x0ecfff:EW, 0x0ed000-0x0edfff:EW, 0x0ee000-0x0eefff:EW, 0x0ef000-0x0effff:EW, 0x0f0000-0x0f0fff:EW, 0x0f1000-0x0f1fff:EW, 0x0f2000-0x0f2fff:EW, 0x0f3000-0x0f3fff:EW, 0x0f4000-0x0f4fff:EW, 0x0f5000-0x0f5fff:EW, 0x0f6000-0x0f6fff:EW, 0x0f7000-0x0f7fff:EW, 0x0f8000-0x0f8fff:EW, 0x0f9000-0x0f9fff:EW, 0x0fa000-0x0fafff:EW, 0x0fb000-0x0fbfff:EW, 0x0fc000-0x0fcfff:S, 0x0fd000-0x0fdfff:S, 0x0fe000-0x0fefff:EW, 0x0ff000-0x0fffff:EW Erase/write done. Verifying flash... VERIFIED. -- Sincerely yours, Alexey Kardapoltsev. +7 (917) 777-10-60

1 0

Fwd: BIOS Write Enable bit problem.
by Rich Futyma Feb. 8, 2013

Feb. 8, 2013

Guys, Does anyone know why bit 0 in the BIOS Control register cannot be set using Intel® X79 Express Chipset. This is what I get when running: flashrom -r /tmp/bios.rom -p internal or flashrom -w xx.rom -p internal *Warning: Setting Bios Control at 0xdc from 0x2a to 0x0b on X79 failed.* *New value is 0x2a.* The read command completes and I get the correct data, but subsequently when I try to erase and program my flash (./flashrom -w xx.rom -p internal:ich_spi_force=yes) I get FCERR (on the first sector erase) which implies that the BIOS is write protected. Thank you in advance for any advice. ---- Rich Futyma ** [image: Inline image 1] CONFIDENTIALITY This e-mail message and any attachments thereto, is intended only for use by the addressee(s) named herein and may contain legally privileged and/or confidential information. If you are not the intended recipient of this e-mail message, you are hereby notified that any dissemination, distribution or copying of this e-mail message, and any attachments thereto, is strictly prohibited. If you have received this e-mail message in error, please immediately notify the sender and permanently delete the original and any copies of this email and any prints thereof. ABSENT AN EXPRESS STATEMENT TO THE CONTRARY HEREINABOVE, THIS E-MAIL IS NOT INTENDED AS A SUBSTITUTE FOR A WRITING. Notwithstanding the Uniform Electronic Transactions Act or the applicability of any other law of similar substance and effect, absent an express statement to the contrary hereinabove, this e-mail message its contents, and any attachments hereto are not intended to represent an offer or acceptance to enter into a contract and are not otherwise intended to bind the sender, Sanmina Corporation (or any of its subsidiaries), or any other person or entity.

1 0

Re: [flashrom] ASUS P5GC: BIOS erased after after `flashrom -r`f (was: a serious problem to solve)
by Paul Menzel Feb. 8, 2013

Feb. 8, 2013

Dear Henry, Am Freitag, den 08.02.2013, 21:41 +0100 schrieb Henry Blanco Lores: > Hello guys, I have subscribed to this mailing list looking for some help > about the use of the flashrom tool. > The problem is this: > > A friend of mine who has just started using Linux, was testing some tools > and not reading carefully their corresponding manuals, he executed this > command: flashrom -r normally that should not cause any problems as it just tries to read the flash chip content. flashrom is very careful to not break anything, so it is very unlikely that the problem was caused by this command. > and this seems to have erased the BIOS of his PC. This is my guess because > he just told me by phone that not even the video signal was working. You have to be very specific. 1. What Linux distribution did your friend use? What version of flashrom? The packaged one? 2. What did your friend exactly do? Did he see any error messages from flashrom. I guess he just shut the system down? > His motherboard is an ASUS P5GC. A similar board seems to be supported [1]. So the problem is even stranger. > Is it possible to recover the BIOS back to the previous state?? If it was really deleted/erased or a bad image was flashed, then you have to reprogram the chip either with a flash chip programmer. One way is to find a motherboard where the chip fits and reprogram it there by hot swapping it. If that is not possible ask around in your local hacker community or find a shop which does it. > Please, I will be looking forward for your comments. I wish you good luck with recovery! You should also join the #flashrom IRC channel on irc.freenode.net. Thanks, Paul [1] http://flashrom.org/Supported_hardware

1 0

Re: [flashrom] a serious problem to solve
by Idwer Vollering Feb. 8, 2013

Feb. 8, 2013

2013/2/8 Henry Blanco Lores <hblanco2009(a)gmail.com>: > Hello guys, I have subscribed to this mailing list looking for some help > about the use of the flashrom tool. > The problem is this: > > A friend of mine who has just started using Linux, was testing some tools > and not reading carefully their corresponding manuals, he executed this > command: flashrom -r > > and this seems to have erased the BIOS of his PC. This is my guess because > he just told me by phone that not even the video signal was working. His > motherboard is an ASUS P5GC. Is it possible to recover the BIOS back to the > previous state?? The above command, 'flashrom -r', will not erase a flash chip. Have your friend either power cycle his machine or remove the mainboard battery (CMOS reset) with mains disconnected. Given the fact that the parameter '-p internal' was not used, he was using an old version of flashrom, version 0.9.3 or older. > > Please, I will be looking forward for your comments. > Thanks in advance. > > H. > > _______________________________________________ > flashrom mailing list > flashrom(a)flashrom.org > http://www.flashrom.org/mailman/listinfo/flashrom

1 0