[SerialICE] Experiencing a qemu segfault (SOLVED) and serialice accessibility problems
Idwer Vollering
vidwer at gmail.com
Fri Aug 27 02:26:36 CEST 2010
2010/8/5 Idwer Vollering <vidwer at gmail.com>
> 2010/8/3 Myles Watson <mylesgw at gmail.com>
>
>> On Tue, Aug 3, 2010 at 10:59 AM, Idwer Vollering <vidwer at gmail.com>
>> wrote:
>>
>> > My problem is two-fold:
>> >
>> > 1) Running the patched qemu segfaults.
>> >
>> > $ sudo ./i386-softmmu/qemu -serialice /dev/ttyUSB0 -hda /dev/zero -L
>> bios/
>> > [sudo] password for idwer:
>> > SerialICE: Open connection to target hardware...
>> > SerialICE: Waiting for handshake with target... target alife!
>> try the latest qemu in the SerialICE tree
>>
>> svn://serialice.com/serialice/trunk/qemu-0.11.0
>>
>> It's already patched, and it has been updated more recently than the
>> patch.
>>
>> > 2) Right now, the serialice shell appears only once: after flashing
>> > serialice.rom and performing a soft reset from vendor bios to serialice.
>> >
>> > SerialICE v1.5 (Aug 3 2010)
>> >
>>
>
Following quote is after soft reset, typing some text and hitting the reset
button:
SerialICE v1.5 (Aug 27 2010)
> 1
> 2
> 3
> 4
> 5
> 6
> 7
> 8
> 9
> 0
> r
> e
> s
> e
> t
> -
> -
> >
> òóñôõöôöòñðôõô÷ôôöðôÿôõõôõôô
>
>> Sounds like SerialICE is depending on some initialization from the
>> vendor BIOS. I guess an ugly way to test it would be to copy the
>> working configuration bits from lspci and hard code them into
>> SerialICE until you find what's wrong.
>>
>
Since the southbridge and superio datasheets mention the existence of two
serial ports, I followed their guidance.
I thought that (the console printing part of) SerialICE, when setup the
correct way, should survive a hard reset/power cycle regardless of the qemu
part is running or not.
Since I don't have an oscilloscope, I've tried setting CLKSEL to 24 MHz and
48 MHz:
pnp_write_register(SUPERIO_CONFIG_PORT, 0x24, 0xb4); // 24 MHz and KBC=1
pnp_write_register(SUPERIO_CONFIG_PORT, 0x24, 0xc4); // 48 MHz and KBC=1
What information is leading, the info from the superio or the info from the
southbridge ?
>
>
> Attached the mainboard code as well.
>
Attaching .config, dmesg, lspci and the patch against svn.
>
>
>> Thanks,
>> Myles
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://serialice.com/pipermail/serialice/attachments/20100827/4e8f16b0/attachment-0001.html>
-------------- next part --------------
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.34-ARCH (thomas at evey) (gcc version 4.5.0 20100610 (prerelease) (GCC) ) #1 SMP PREEMPT Tue Aug 10 21:38:22 CEST 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001f740000 (usable)
BIOS-e820: 000000001f740000 - 000000001f750000 (ACPI data)
BIOS-e820: 000000001f750000 - 000000001f800000 (ACPI NVS)
BIOS-e820: 00000000ffbc0000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
DMI 2.3 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x1f740 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-DFFFF uncachable
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask FE0000000 write-back
1 base 01F800000 mask FFF800000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009fc00 (usable)
modified: 000000000009fc00 - 00000000000a0000 (reserved)
modified: 00000000000e6000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000001f740000 (usable)
modified: 000000001f740000 - 000000001f750000 (ACPI data)
modified: 000000001f750000 - 000000001f800000 (ACPI NVS)
modified: 00000000ffbc0000 - 0000000100000000 (reserved)
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-000000001f740000
0000000000 - 0000400000 page 4k
0000400000 - 001f400000 page 2M
001f400000 - 001f740000 page 4k
kernel direct mapping tables up to 1f740000 @ 15000-1a000
RAMDISK: 177f2000 - 179b0000
ACPI: RSDP 000fa720 00014 (v00 ACPIAM)
ACPI: RSDT 1f740000 00030 (v01 A M I OEMRSDT 07000817 MSFT 00000097)
ACPI: FACP 1f740200 00081 (v02 A M I OEMFACP 07000817 MSFT 00000097)
ACPI: DSDT 1f740360 03854 (v01 I65GV I65GV223 00000223 INTL 02002026)
ACPI: FACS 1f750000 00040
ACPI: APIC 1f740300 0005C (v01 A M I OEMAPIC 07000817 MSFT 00000097)
ACPI: OEMB 1f750040 0003F (v01 A M I OEMBIOS 07000817 MSFT 00000097)
ACPI: Local APIC address 0xfee00000
0MB HIGHMEM available.
503MB LOWMEM available.
mapped low ram: 0 - 1f740000
low ram: 0 - 1f740000
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x0001f740
HighMem empty
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0001f740
On node 0 totalpages: 128719
free_area_init_node: node 0, pgdat c1402fc0, node_mem_map c1562200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 975 pages used for memmap
Normal zone: 123761 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000
PM: Registered nosave memory: 00000000000e6000 - 0000000000100000
Allocating PCI resources starting at 1f800000 (gap: 1f800000:e03c0000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
early_res array is doubled to 64 at [16000 - 167ff]
PERCPU: Embedded 14 pages/cpu @c1c00000 s34388 r0 d22956 u2097152
pcpu-alloc: s34388 r0 d22956 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 127712
Kernel command line: BOOT_IMAGE=/vmlinuz26 root=/dev/sda3
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
allocated 2576320 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Subtract (39 early reservations)
#1 [0000001000 - 0000002000] EX TRAMPOLINE
#2 [0001000000 - 0001559d84] TEXT DATA BSS
#3 [00177f2000 - 00179b0000] RAMDISK
#4 [000009fc00 - 0000100000] BIOS reserved
#5 [000155a000 - 000156008d] BRK
#6 [0000010000 - 0000011000] TRAMPOLINE
#7 [0000011000 - 0000015000] ACPI WAKEUP
#8 [0000015000 - 0000016000] PGTABLE
#9 [0001561000 - 0001562000] BOOTMEM
#10 [0001562000 - 0001952000] BOOTMEM
#11 [0001559dc0 - 0001559dc4] BOOTMEM
#12 [0001559e00 - 0001559ec0] BOOTMEM
#13 [0001559ec0 - 0001559ef0] BOOTMEM
#14 [0001952000 - 0001953800] BOOTMEM
#15 [0001559f00 - 0001559f27] BOOTMEM
#16 [00015600c0 - 00015601a0] BOOTMEM
#17 [0001559f40 - 0001559f80] BOOTMEM
#18 [0001559f80 - 0001559fc0] BOOTMEM
#19 [0001559fc0 - 000155a000] BOOTMEM
#20 [00015601c0 - 0001560200] BOOTMEM
#21 [0001560200 - 0001560240] BOOTMEM
#22 [0001560240 - 0001560280] BOOTMEM
#23 [0001560280 - 00015602c0] BOOTMEM
#24 [00015602c0 - 00015602d0] BOOTMEM
#25 [0001560300 - 0001560325] BOOTMEM
#26 [0001560340 - 0001560365] BOOTMEM
#27 [0001c00000 - 0001c0e000] BOOTMEM
#28 [0001e00000 - 0001e0e000] BOOTMEM
#29 [0001560380 - 0001560384] BOOTMEM
#30 [00015603c0 - 00015603c4] BOOTMEM
#31 [0001560400 - 0001560408] BOOTMEM
#32 [0001560440 - 0001560448] BOOTMEM
#33 [0001560480 - 0001560528] BOOTMEM
#34 [0001560540 - 00015605a8] BOOTMEM
#35 [0001953800 - 0001955800] BOOTMEM
#36 [0001955800 - 0001995800] BOOTMEM
#37 [0001995800 - 00019b5800] BOOTMEM
#38 [0001e0e000 - 0002082fc0] BOOTMEM
Initializing HighMem for node 0 (00000000:00000000)
Memory: 500496k/515328k available (2930k kernel code, 14380k reserved, 1208k data, 404k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff1e000 - 0xfffff000 ( 900 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xdff40000 - 0xff7fe000 ( 504 MB)
lowmem : 0xc0000000 - 0xdf740000 ( 503 MB)
.init : 0xc140b000 - 0xc1470000 ( 404 kB)
.data : 0xc12dca4c - 0xc140adc0 (1208 kB)
.text : 0xc1000000 - 0xc12dca4c (2930 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:512
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 2999.802 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 6002.58 BogoMIPS (lpj=9999340)
Security Framework initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 4 MCE banks
Disabling lock debugging due to kernel taint
CPU0: Thermal monitoring enabled (TM1)
Performance Events: no PMU driver, software events only.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20100121
Enabling APIC mode: Flat. Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Booting Node 0, Processors #1 Ok.
Initializing CPU#1
Brought up 2 CPUs
Total of 2 processors activated (12003.51 BogoMIPS).
devtmpfs: initialized
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI Warning: Incorrect checksum in table [OEMB] - B7, should be B2 (20100121/tbutils-314)
ACPI: No dock devices found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
pci_root PNP0A03:00: host bridge window [mem 0x1f800000-0xffefffff]
pci 0000:00:00.0: Enabling MCH 'Overflow' Device
pci 0000:00:00.0: reg 10: [mem 0xfe800000-0xfebfffff pref]
pci 0000:00:02.0: reg 10: [mem 0xf0000000-0xf7ffffff pref]
pci 0000:00:02.0: reg 14: [mem 0xfe780000-0xfe7fffff]
pci 0000:00:02.0: reg 18: [io 0xec00-0xec07]
pci 0000:00:06.0: reg 10: [mem 0xfecf0000-0xfecf0fff]
pci 0000:00:1d.0: reg 20: [io 0xdc00-0xdc1f]
pci 0000:00:1d.1: reg 20: [io 0xe000-0xe01f]
pci 0000:00:1d.2: reg 20: [io 0xe400-0xe41f]
pci 0000:00:1d.3: reg 20: [io 0xe800-0xe81f]
pci 0000:00:1d.7: reg 10: [mem 0xfe77bc00-0xfe77bfff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH4 GPIO
pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
pci 0000:00:1f.1: reg 20: [io 0xfc00-0xfc0f]
pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff]
pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
pci 0000:00:1f.5: reg 10: [io 0xd800-0xd8ff]
pci 0000:00:1f.5: reg 14: [io 0xd400-0xd43f]
pci 0000:00:1f.5: reg 18: [mem 0xfe77b800-0xfe77b9ff]
pci 0000:00:1f.5: reg 1c: [mem 0xfe77b400-0xfe77b4ff]
pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.5: PME# disabled
pci 0000:01:05.0: reg 10: [io 0xb800-0xb8ff]
pci 0000:01:05.0: reg 14: [mem 0xfe5ffc00-0xfe5ffcff]
pci 0000:01:05.0: supports D1 D2
pci 0000:01:05.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:01:05.0: PME# disabled
pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0xb000-0xbfff]
pci 0000:00:1e.0: bridge window [mem 0xfe500000-0xfe5fffff]
pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x1f800000-0xffefffff] (subtractive decode)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 *6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
Expanded resource reserved due to conflict with PCI Bus 0000:00
reserve RAM buffer: 000000000009fc00 - 000000000009ffff
reserve RAM buffer: 000000001f740000 - 000000001fffffff
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
system 00:06: [io 0x04d0-0x04d1] has been reserved
system 00:06: [io 0x0800-0x087f] has been reserved
system 00:06: [io 0x0480-0x04bf] has been reserved
system 00:06: [mem 0xfed20000-0xfed8ffff] has been reserved
system 00:06: [mem 0xffb00000-0xffbfffff] has been reserved
system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:09: [io 0x0680-0x06ff] has been reserved
system 00:09: [io 0x0295-0x0296] has been reserved
system 00:0a: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:0a: [mem 0x000c0000-0x000dffff] could not be reserved
system 00:0a: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:0a: [mem 0x00100000-0x1f7fffff] could not be reserved
system 00:0a: [mem 0xfff00000-0xffffffff] has been reserved
pci 0000:00:1f.1: BAR 5: assigned [mem 0x1f800000-0x1f8003ff]
CPU1: Temperature above threshold, cpu clock throttled (total events = 1)
CPU0: Temperature above threshold, cpu clock throttled (total events = 1)
pci 0000:00:1f.1: BAR 5: set to [mem 0x1f800000-0x1f8003ff] (PCI address [0x1f800000-0x1f8003ff]
pci 0000:00:1e.0: PCI bridge to [bus 01-01]
pci 0000:00:1e.0: bridge window [io 0xb000-0xbfff]
pci 0000:00:1e.0: bridge window [mem 0xfe500000-0xfe5fffff]
CPU1: Temperature/speed normal
CPU0: Temperature/speed normal
pci 0000:00:1e.0: bridge window [mem pref disabled]
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x1f800000-0xffefffff]
pci_bus 0000:01: resource 0 [io 0xb000-0xbfff]
pci_bus 0000:01: resource 1 [mem 0xfe500000-0xfe5fffff]
pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:01: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:01: resource 7 [mem 0x1f800000-0xffefffff]
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
PCI: CLS 0 bytes, default 64
Unpacking initramfs...
Freeing initrd memory: 1784k freed
apm: BIOS not found.
Scanning for low memory corruption every 60 seconds
audit: initializing netlink socket (disabled)
type=2000 audit(1282873106.319:1): initialized
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 981
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
PM: Resume from disk failed.
registered taskstats version 1
Initalizing network drop monitor service
Freeing unused kernel memory: 404k freed
udev: starting version 161
SCSI subsystem initialized
libata version 3.00 loaded.
pata_acpi 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pata_acpi 0000:00:1f.1: setting latency timer to 64
pata_acpi 0000:00:1f.1: PCI INT A disabled
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
ata1.00: ATA-5: WDC WD600BB-00CAA1, 17.07W17, max UDMA/100
ata1.00: 117231408 sectors, multi 16: LBA
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA WDC WD600BB-00CA 17.0 PQ: 0 ANSI: 5
ata2.00: ATA-7: Maxtor 6E040L0, NAR61590, max UDMA/133
ata2.00: 80293248 sectors, multi 16: LBA
ata2.01: ATA-6: ST380011A, 8.01, max UDMA/100
ata2.01: 156301488 sectors, multi 16: LBA48
ata2.00: limited to UDMA/33 due to 40-wire cable
ata2.01: limited to UDMA/33 due to 40-wire cable
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 1:0:0:0: Direct-Access ATA Maxtor 6E040L0 NAR6 PQ: 0 ANSI: 5
scsi 1:0:1:0: Direct-Access ATA ST380011A 8.01 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 80293248 512-byte logical blocks: (41.1 GB/38.2 GiB)
sda:
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:1:0: [sdc] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
sdb1: <bsd:
sd 1:0:1:0: [sdc] Write Protect is off
sd 1:0:1:0: [sdc] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb5 sdb6 sdb7 sdb8 sdb9 >
sdc: sda1 sda2 sda3 sda4
sdc1 sdc2 sdc3 sdc4 <
sd 0:0:0:0: [sda] Attached SCSI disk
sdc5 sdc6 sdc7 sdc8
sd 1:0:0:0: [sdb] Attached SCSI disk
sdc9 sdc10 >
sd 1:0:1:0: [sdc] Attached SCSI disk
EXT4-fs (sda3): INFO: recovery required on readonly filesystem
EXT4-fs (sda3): write access will be enabled during recovery
EXT4-fs (sda3): recovery complete
EXT4-fs (sda3): mounted filesystem with ordered data mode
udev: starting version 161
input: PC Speaker as /devices/platform/pcspkr/input/input0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 1:0:1:0: Attached scsi generic sg2 type 0
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
intel_rng: FWH not detected
Linux agpgart interface v0.103
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:01:05.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
lp: driver loaded but no devices found
parport_pc 00:05: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
agpgart-intel 0000:00:00.0: Intel 865 Chipset
agpgart-intel 0000:00:00.0: detected 8060K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xf0000000
8139too: 8139too Fast Ethernet driver 0.9.28
8139too 0000:01:05.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
8139too 0000:01:05.0: eth0: RealTek RTL8139 at 0xdff78c00, 00:19:66:99:46:bc, IRQ 22
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
lp0: using parport0 (interrupt-driven).
ehci_hcd 0000:00:1d.7: debug port 1
rtc_cmos 00:02: RTC can wake from S4
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe77bc00
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
[drm] Initialized drm 1.1.0 20060810
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000dc00
ppdev: user-space parallel port driver
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e400
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e800
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Intel ICH 0000:00:1f.5: setting latency timer to 64
usb 1-6: new high speed USB device using ehci_hcd and address 3
intel8x0_measure_ac97_clock: measured 52628 usecs (2536 samples)
intel8x0: clocking to 48000
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
[drm] set up 7M of stolen space
[drm] initialized overlay support
usb 2-2: new low speed USB device using uhci_hcd and address 2
cfg80211: Calling CRDA to update world regulatory domain
Console: switching to colour frame buffer device 180x56
fb0: inteldrmfb frame buffer device
registered panic notifier
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
usbcore: registered new interface driver hiddev
input: CHESEN PS2 to USB Converter as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input3
generic-usb 0003:0A81:0205.0001: input,hidraw0: USB HID v1.10 Keyboard [CHESEN PS2 to USB Converter] on usb-0000:00:1d.0-2/input0
input: CHESEN PS2 to USB Converter as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input4
generic-usb 0003:0A81:0205.0002: input,hidraw1: USB HID v1.10 Mouse [CHESEN PS2 to USB Converter] on usb-0000:00:1d.0-2/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
phy0: Selected rate control algorithm 'minstrel'
Registered led device: rt73usb-phy0::radio
Registered led device: rt73usb-phy0::assoc
Registered led device: rt73usb-phy0::quality
usbcore: registered new interface driver rt73usb
EXT4-fs (sda4): mounted filesystem with ordered data mode
Adding 265068k swap on /dev/sda2. Priority:-1 extents:1 across:265068k
rt73usb 1-6:1.0: firmware: requesting rt73.bin
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: deauthenticating from 00:18:f8:74:bd:2a by local choice (reason=3)
wlan0: authenticate with 00:18:f8:74:bd:2a (try 1)
wlan0: authenticate with 00:18:f8:74:bd:2a (try 2)
wlan0: authenticated
wlan0: associate with 00:18:f8:74:bd:2a (try 1)
wlan0: RX AssocResp from 00:18:f8:74:bd:2a (capab=0x431 status=0 aid=2)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
cfg80211: Calling CRDA for country: DE
padlock: VIA PadLock not detected.
wlan0: no IPv6 routers present
-------------- next part --------------
A non-text attachment was scrubbed...
Name: .config
Type: application/xml
Size: 1388 bytes
Desc: not available
URL: <http://serialice.com/pipermail/serialice/attachments/20100827/4e8f16b0/attachment-0001.wsdl>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: serialice-r105_asrock_p4i65gv.patch
Type: text/x-diff
Size: 2651 bytes
Desc: not available
URL: <http://serialice.com/pipermail/serialice/attachments/20100827/4e8f16b0/attachment-0001.bin>
-------------- next part --------------
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] (rev 02)
Subsystem: ASRock Incorporation Device [1849:2570]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fe800000 (32-bit, prefetchable) [size=4M]
Capabilities: [e4] Vendor Specific Information: Len=06 <?>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00: 86 80 70 25 06 00 90 20 02 00 00 06 00 00 00 00
10: 08 00 80 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 70 25
30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 34 00 40 80 1c 00 00 00 00 00 00 00 00 00
60: 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 10 11 01 00 00 33 33 00 00 00 00 00 00 0a 38 00
a0: 02 00 30 00 17 42 00 1f 00 00 00 00 00 00 00 00
b0: 00 00 00 00 3f 00 00 00 00 00 00 00 20 10 00 00
c0: 00 00 00 00 80 1f 0e 24 00 01 00 00 00 00 00 00
d0: 02 28 04 0e 0b 0d 00 00 00 00 00 00 00 00 40 01
e0: 00 00 00 00 09 00 06 11 00 02 00 00 00 00 00 00
f0: 00 00 00 00 02 00 00 00 68 0f 03 00 00 00 00 00
00:02.0 VGA compatible controller [0300]: Intel Corporation 82865G Integrated Graphics Controller [8086:2572] (rev 02) (prog-if 00 [VGA controller])
Subsystem: ASRock Incorporation Device [1849:2572]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at fe780000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at ec00 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: i915
Kernel modules: i915
00: 86 80 72 25 07 00 90 00 02 00 00 03 00 00 00 00
10: 08 00 00 f0 00 00 78 fe 01 ec 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 72 25
30: 00 00 00 00 d0 00 00 00 00 00 00 00 0a 01 00 00
40: 00 00 00 00 e0 23 e0 11 00 00 00 00 00 00 00 00
50: 00 00 34 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 01 02 ff 00 00 00 71 02 10 20
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 55 ff ff 55 ff ff 00 00
b0: 08 04 41 00 30 08 04 00 85 21 ff df b2 40 68 00
c0: 00 00 00 00 80 1f 0e 24 00 00 00 00 00 00 00 00
d0: 01 00 21 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 01 00 00 00 09 00 06 11 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 68 0f 03 00 00 00 00 00
00:06.0 System peripheral [0880]: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface [8086:2576] (rev 02)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at fecf0000 (32-bit, non-prefetchable) [size=4K]
00: 86 80 76 25 02 00 80 00 02 00 80 08 00 00 00 00
10: 00 00 cf fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 43 65 10 04 00 00 00 00 04 00 00 00 00 00 00 00
50: 01 00 80 00 02 01 80 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 55 05 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 20 08 00
b0: 00 00 00 00 f0 43 fc 7d 01 00 00 00 09 00 00 00
c0: 00 08 00 00 20 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 ff ff ff ff ff ff ff 3f
e0: 01 00 00 00 00 00 01 02 ff 0e 00 00 00 00 04 00
f0: 00 0c 02 00 00 00 00 00 68 0f 03 00 74 f8 00 00
00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASRock Incorporation Device [1849:24d0]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at dc00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00: 86 80 d2 24 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 dc 00 00 00 00 00 00 00 00 00 00 49 18 d0 24
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00
00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASRock Incorporation Device [1849:24d0]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at e000 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00: 86 80 d4 24 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e0 00 00 00 00 00 00 00 00 00 00 49 18 d0 24
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00
00:1d.2 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASRock Incorporation Device [1849:24d0]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e400 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00: 86 80 d7 24 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e4 00 00 00 00 00 00 00 00 00 00 49 18 d0 24
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00
00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASRock Incorporation Device [1849:24d0]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00: 86 80 de 24 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e8 00 00 00 00 00 00 00 00 00 00 49 18 d0 24
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00
00:1d.7 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller [8086:24dd] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASRock Incorporation Device [1849:24d0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at fe77bc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00: 86 80 dd 24 06 01 90 02 02 20 03 0c 00 00 00 00
10: 00 bc 77 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 d0 24
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 04 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00
60: 20 20 ff 01 00 00 00 00 01 00 00 00 00 00 08 c0
70: 00 00 dd 3f 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 55 55 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 80 00 00 88 83 40 00 66 0f 05 00 06 14 00 00
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fe500000-fe5fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00: 86 80 4e 24 07 01 80 00 c2 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 20 b0 b0 80 02
20: 50 fe 50 fe f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
40: 02 28 30 76 00 00 00 00 00 00 00 00 00 00 00 00
50: 02 64 73 00 00 00 00 00 50 01 34 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 01 00 02 00 00 00 c0 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 51 33
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge [8086:24d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: iTCO_wdt, intel-rng
00: 86 80 d0 24 0f 00 80 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 08 00 00 10 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 81 04 00 00 10 00 00 00
60: 8a 86 85 83 d0 00 00 00 80 80 85 8b 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: ff fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 20 02 00 00 39 00 00 00 0d 00 00 00 00 03 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 02 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 86 21 02 00 02 00 00 00 04 00 00 00 00 00 00 00
e0: 00 00 00 80 00 00 08 14 33 22 11 00 00 00 67 45
f0: 00 00 44 00 04 00 00 00 66 0f 05 3e 00 00 00 00
00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller [8086:24db] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: ASRock Incorporation Device [1849:24d0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 1f800000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
Kernel modules: ata_piix, piix
00: 86 80 db 24 07 00 80 02 02 8a 01 01 00 00 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: 01 fc 00 00 00 00 80 1f 00 00 00 00 49 18 d0 24
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
40: 07 e3 77 e3 b0 00 00 00 0d 00 01 22 00 00 00 00
50: 00 00 00 00 30 10 00 00 00 00 00 00 00 00 00 00
60: 08 00 00 00 00 00 00 00 08 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller [8086:24d3] (rev 02)
Subsystem: ASRock Incorporation Device [1849:24d0]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 49 18 d0 24
30: 00 00 00 00 00 00 00 00 00 00 00 00 06 02 00 00
40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)
Subsystem: ASRock Incorporation Device [1849:9739]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at d400 [size=64]
Region 2: Memory at fe77b800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at fe77b400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00: 86 80 d5 24 07 00 90 02 02 00 01 04 00 00 00 00
10: 01 d8 00 00 01 d4 00 00 00 b8 77 fe 00 b4 77 fe
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 39 97
30: 00 00 00 00 50 00 00 00 00 00 00 00 06 02 00 00
40: 09 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 00 c2 c9 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 66 0f 05 00 00 00 00 00
01:05.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: ASRock Incorporation Device [1849:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at fe5ffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: 8139too
Kernel modules: 8139too, 8139cp
00: ec 10 39 81 07 00 90 02 10 00 00 02 00 20 00 00
10: 01 b8 00 00 00 fc 5f fe 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 39 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 20 40
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 00 c2 f7 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
More information about the SerialICE
mailing list