flashrom v0.9.9-r1954 on Linux 4.12.0-rc1-wt-ath+ (x86_64) flashrom is free software, get the source code at https://flashrom.org flashrom was built with libpci 3.3.1, GCC 5.3.1 20160424, little endian Command line (7 args): flashrom -V --programmer internal:laptop=this_is_not_a_laptop -c W25Q64.W -r test.img Calibrating delay loop... OS timer resolution is 1 usecs, 1186M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1003 us, 10000 myus = 10001 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. Using Internal DMI decoder. DMI string chassis-type: "Other" DMI chassis-type is not specific enough. DMI string system-manufacturer: "Default string" DMI string system-product-name: "Default string" DMI string system-version: "Default string" DMI string baseboard-manufacturer: "AMI Corporation" DMI string baseboard-product-name: "Aptio CRB" DMI string baseboard-version: "Default string" Found chipset "Intel Braswell" with PCI ID 8086:229c. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom@flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... Root Complex Register Block address = 0xfed1c000 GCS = 0xc01: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap: not enabled 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes SPI_BASE_ADDRESS = 0xfed01000 SPI Read Configuration: prefetching disabled, caching enabled, BIOS_CNTL = 0x01: BIOS Lock Enable: disabled, BIOS Write Enable: enabled 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 Reading OPCODES... done 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x50: 0x0000ffff (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff 0x54: 0x00000000 FREG0: Flash Descriptor region (0x00000000-0x00000fff) is read-write. 0x58: 0x07ff0300 FREG1: BIOS region (0x00300000-0x007fffff) is read-write. 0x5C: 0x02ff0001 FREG2: Management Engine region (0x00001000-0x002fffff) is read-write. 0x90: 0xc4 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf87f10 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=0 0x94: 0x0006 (PREOP) 0x96: 0x843b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x5a00019f (OPMENU+4) 0xC4: 0x00802025 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002025 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20 0xD0: 0xffffffff (FPB) OK. The following protocols are supported: FWH, SPI. Probing for Winbond W25Q64.W, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x6017 Found Winbond flash chip "W25Q64.W" (8192 kB, SPI) mapped at physical address 0x00000000ff800000. Chip status register is 0x00. This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). Reading flash... done. Restoring MMIO space at 0x7f6dfa04b0fc