<div dir="ltr"><div dir="ltr"><div>Hi Daniel,</div><div><br></div><div>Thanks for your reply, but it's not the case with me.</div><div><br></div><div>I'm not using DDR3L-RDIMMs. My dmidecode output of one DIMM is:</div><div><br></div><div>Handle 0x0007, DMI type 17, 40 bytes<br>Memory Device<br>    Array Handle: 0x0006<br>    Error Information Handle: Not Provided<br>    Total Width: 72 bits<br>    Data Width: 64 bits<br>    Size: 16384 MB<br>    Form Factor: DIMM<br>    Set: None<br>    Locator: NODE 0 DIMM_A2<br>    Bank Locator: Not Specified<br>    Type: DDR3<br>    Type Detail: Synchronous Registered (Buffered)<br>    Speed: 800 MT/s<br>    Manufacturer: Samsung<br>    Serial Number: 7FCC9C13<br>    Asset Tag: Not Specified<br>    Part Number: M393B2G70BH0-CK0  <br>    Rank: 2<br>    Configured Memory Speed: 800 MT/s<br>    Minimum Voltage: 1.5 V<br>    Maximum Voltage: 1.5 V<br>    Configured Voltage: 1.5 V<br></div><div><br></div><div>Iru<br></div><div><br><div class="gmail_quote"><div dir="ltr">On Sat, Oct 6, 2018 at 3:58 AM Daniel Kulesz <<a href="mailto:daniel.ina1@googlemail.com">daniel.ina1@googlemail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Hi Iru,<br>
<br>
> I just found the memory performance on KGPE-D16 is lower when running with<br>
> coreboot. I have two Opteron 6276 and 8 16GB DDR3-1600 RDIMM on all orange<br>
> slots. I tested it with `hdparm -tT /dev/sda` and see the `Timing cached<br>
> reads` result. With coreboot, this value is around 3000 MB/s, but with OEM<br>
> firmware it can go to around 3600 MB/s. I think the disk cached read speed<br>
> is related to memory performance.<br>
<br>
Are you using DDR3L-RDIMMs? And did you check whether your memory really runs at 800 MHz? My experience is that coreboot sets the clock down to 667 MHz when running on 1.35V (low voltage), while the vendor bios seems to run modules at 800 MHz in low voltage mode,  resulting in higher performance. According to Timothy, this is  "over the spec" and thus not set in coreboot by default (you can choose between 1.5V 800 MHz or 1.35V at 667 MHz - but may depend on the used modules).<br>
<br>
You can check e.g. in dmidecode. Below is an example (serial number x'd out):<br>
<br>
Handle 0x000E, DMI type 17, 40 bytes<br>
Memory Device<br>
        Array Handle: 0x0006<br>
        Error Information Handle: Not Provided<br>
        Total Width: 72 bits<br>
        Data Width: 64 bits<br>
        Size: 8192 MB<br>
        Form Factor: DIMM<br>
        Set: None<br>
        Locator: NODE 0 DIMM_D2<br>
        Bank Locator: Not Specified<br>
        Type: DDR3<br>
        Type Detail: Synchronous Registered (Buffered)<br>
        Speed: 800 MHz<br>
        Manufacturer: Samsung<br>
        Serial Number: xxxxxxxxx<br>
        Asset Tag: Not Specified<br>
        Part Number: M393B1K70DH0-YK0  <br>
        Rank: 2<br>
        Configured Clock Speed: 800 MHz<br>
        Minimum Voltage: 1.35 V<br>
        Maximum Voltage: 1.5 V<br>
        Configured Voltage: 1.5 V<br>
<br>
Btw.: I am getting around 3700 MB/sec with hdparm -Tt on my /dev/sda (mechanical disk) and around 3840 MB/sec on /dev/nvme0n1 (PCIe M.2 SSD).<br>
<br>
Cheers, Daniel<br>
</blockquote></div><br clear="all"><br>-- <br><div dir="ltr" class="gmail_signature"><div dir="ltr"><div><div>My website: <a href="https://vimacs.lcpu.club" target="_blank">https://vimacs.lcpu.club</a><br></div><div dir="ltr"><br></div><div dir="ltr">Please do not send me Microsoft Office/Apple iWork documents. Send OpenDocument instead! <a href="http://fsf.org/campaigns/opendocument/" target="_blank">http://fsf.org/campaigns/opendocument/</a></div></div></div></div></div></div></div>