<p dir="ltr">Better here, sorry.<br>
<a href="https://github.com/osresearch/heads/issues/134">https://github.com/osresearch/heads/issues/134</a></p>
<br><div class="gmail_quote"><div dir="ltr">Le ven. 23 févr. 2018 00:26, Thierry Laurion <<a href="mailto:thierry.laurion@gmail.com">thierry.laurion@gmail.com</a>> a écrit :<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><p dir="ltr">Actually if others of you want to contribute, there is this heads kgpe-d16 port that permits to flash directly from the heads coreboot payload with Timothy's patches on the flashrom tools. You may want to take a look here :<br>
<a href="https://github.com/flammit/heads/pull/9#issuecomment-362022411" target="_blank">https://github.com/flammit/heads/pull/9#issuecomment-362022411</a></p>
<br><div class="gmail_quote"><div dir="ltr">Le jeu. 22 févr. 2018 16:37, Timothy Pearson <<a href="mailto:tpearson@raptorengineering.com" target="_blank">tpearson@raptorengineering.com</a>> a écrit :<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Actually, for OpenBMC work, hotplugging is often the only way to go.<br>
Just be very careful to align the pins correctly the first time; you<br>
don't have a second chance if you misalign the pins and fry the module...<br>
<br>
On 02/22/2018 03:22 PM, <a href="mailto:Taiidan@gmx.com" target="_blank">Taiidan@gmx.com</a> wrote:<br>
> On 02/17/2018 09:46 AM, Elisenda Cuadros wrote:<br>
><br>
>> Hi,<br>
>><br>
>> Now I trying to use your OpenBMC port.<br>
>><br>
>> I followed the instructions and everything was fine (compiling,<br>
>> reading and flashing). I waited several minutes after flashing, but<br>
>> the module didn 't blinked like in the vendor rom, nor did it receive<br>
>> an ip.<br>
>><br>
>> I halted the system because I thought maybe it needs a cold start.<br>
>><br>
>> After this, the system doesn't boot with the module plugged in. The<br>
>> fans begin to spin for approximately 1/4 second, but nothing else.<br>
>><br>
>> My two fans (1 cpu & 1 chassis) have 3 pins and are low speed (~1000rpm)<br>
>><br>
>> In the case I have to reflash the module, is it possible to hotplug it?<br>
> Hotplugging is dangerous and not supported, don't do it.<br>
>> Thank you very much for your support.<br>
> You can use a test clip to externally flash it via a flashing device<br>
> (not sure which can do 16 pins though, I would inquire on the flashrom<br>
> mailinglist)<br>
><br>
> Are you using the latest coreboot? AFAIK coreboot was patched to support<br>
> OpenBMC, so you need a new version with the patches.<br>
<br>
<br>
--<br>
Timothy Pearson<br>
Raptor Engineering<br>
+1 (415) 727-8645 (direct line)<br>
+1 (512) 690-0200 (switchboard)<br>
<a href="https://www.raptorengineering.com" rel="noreferrer" target="_blank">https://www.raptorengineering.com</a><br>
<br>
--<br>
coreboot mailing list: <a href="mailto:coreboot@coreboot.org" target="_blank">coreboot@coreboot.org</a><br>
<a href="https://mail.coreboot.org/mailman/listinfo/coreboot" rel="noreferrer" target="_blank">https://mail.coreboot.org/mailman/listinfo/coreboot</a><br>
</blockquote></div></blockquote></div>